NEC MultiSync FP1370 Скачать руководство пользователя страница 30

Страница: 30 / 286

5-1

ADJUSTMENT PROCEDURES

Application

These specifications outline the adjustment procedures for Model FP1370 (A)/(B) 22-inch color monitor.

Model Name:

FP1370 (A)/(B)

Destination:

North America, Europe Standard Adjustment Conditions

Standard Adjustment Conditions

1. Power Supply Voltage

A / B Version:

AC 100V

5% 50/60Hz or AC 120V

5% 60Hz or

AC 220V

5% 50Hz

2. Warm Up

Adjust this monitor after a minimum of 90 minutes to allow unit to reach ambient operating temperature.

(Use the Self Test screen. Refer item 7-5-3. about Self Test. )

※

Adjust the monitor according to item

“

Rough Adjustment before warm up

”

before warm up.

※

When aging, cover with back cabinet or aging jig.

3. Signals

Unless otherwise specified, adjustment should be Mini D-SUB 15 pins.

Video: Analog

0.7

0.01 Vp-p Positive polarity (terminated at 75 ohms

1%)

or Analog sync. on green

Video 0.7

0.01 Vp-p positive polarity

Sync 0.3

0.01 Vp-p negative polarity

(terminated at 75 ohms

1%)

Sync.:

TTL level (High level : more than 2.4V / Low level : less than 0.8V)

H/V separate, positive / negative polarity

or H/V composite, positive / negative polarity

or Sync. on green, 0.3

0.01 Vp-p negative polarity

(terminated at 75 ohms

1%)

Содержание MultiSync FP1370































































































































































































































































































Результаты поиска

Содержание MultiSync FP1370

Отзывы:

Похожие инструкции для MultiSync FP1370

Бренды по названию

Популярные бренды

NEC MultiSync FP1370, Руководство по обслуживанию

Результаты поиска

Содержание MultiSync FP1370

Отзывы:

Похожие инструкции для MultiSync FP1370

Бренды по названию

Популярные бренды