NEC MultiSync FP1370 Скачать руководство пользователя страница 92

Страница: 92 / 286

7-4

2. ABNORMAL VIDEO ON CRT SCREEN (too dark or too bright)

* Input 1/4 window pattern.

Set up BRIGHTNESS:preset, CONTRAST:max. and R/G/B control:all max. at OSM menu.

Measure R/G/B video outputs at TP-R, TP-G and TP-B on the CRT PWB (PWE-567C).

Normally, R/G/B video output voltages are approx. 45Vp-p with 1/4 window pattern input

when the contrast control of the OSM menu is MAX.

Measure the video output at IC721 pins 6(R), 14(G) and 4(B) on VIDEO
PWB (PWE-567A).
Normally, the wave form is same as upon figure.

Measure the voltage at CNP 3 on the VIDEO PWB(PWE-567A).

1) Check the voltage at C726 on the VIDEO PWB(PWE-567A). The voltage

is approx. 9.1V

2) Check the voltage at R728 (reverse of ZD721) on the VIDEO PWB

(PWE-567A). The voltage is approx. 12V

Measure the video input at IC721 pins 8(R), 12(G) and 2(B) on VIDEO PWB
(PWE-567A). The voltage is approx. 5Vp-p.

Measure the video output at IC711 pins 32(R), 29(G) and 35(B) on VIDEO
PWB (PWE-567A). The voltage is approx. 3Vp-p.

CONTINUE 1

CONTINUE 2

Check R/G/B

video output

45 Vp-p

Check IC721

output (VIDEO)

C729R/G/B failure, or CN-SG Failure.

Check 80V line

CN-P failure, or check SW-REG (see item 13)

Check Vbb line

and 12V line

1) ZD721, C726, R728 failure.

2) CN-AF failure.

Check IC721

input (VIDEO)

IC721 failure.

Check IC711

output (VIDEO)

Содержание MultiSync FP1370































































































































































































































































































Результаты поиска

Содержание MultiSync FP1370

Отзывы:

Похожие инструкции для MultiSync FP1370

Бренды по названию

Популярные бренды

NEC MultiSync FP1370, Руководство по обслуживанию

Результаты поиска

Содержание MultiSync FP1370

Отзывы:

Похожие инструкции для MultiSync FP1370

Бренды по названию

Популярные бренды