NEC Express5800/110Ge Скачать руководство пользователя страница 222

Страница: 222 / 332

9-12 Upgrading Your Server

Installation

Follow the procedure as described below to install 3.5-inch hard disk drives.

Configure the operation mode of hard disk drives according to the manual supplied with
the hard disk drive.

Hard disk drive

Bay to Install

Serial ATA connector on mother board

First hard disk drive

Top

Serial ATA connector 1

Second hard disk drive

Upper Middle

Serial ATA connector 2

Third hard disk drive

Lower Middle

Serial ATA connector 3

Fourth hard disk drive

Bottom

Serial ATA connector 4

See the section "Preparing for Installation and Removal" described earlier to prepare.

Remove the left side cover and front mask.

Disconnect the power cable, IDE cable, and FDD cable from the mother board.

Disconnect the interface cable and power cord from the hard disk drive if connected.

Serial ATA

connector 3

Serial ATA

connector 1

Serial ATA

connector 4

Serial ATA

connector 2

Содержание Express5800/110Ge













































































































































































































































































































































Результаты поиска

Содержание Express5800/110Ge

Отзывы:

NEC Express5800/110Ge, Руководство пользователя, Страница: 222 / 332

Результаты поиска

Содержание Express5800/110Ge

Отзывы: