NEC Express5800/110Ge Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 332

NEC Express5800/110Ge Скачать руководство пользователя страница 104

4-44 Configuring Your Server

7.

Press

F10

to create virtual drive.

The "Virtual Drives Configured" screen appears. (The figure below shows an example of
RAID1 configured with two hard disk drives.)

8.

Select "RAID," "Size", "DWC", "RA", or "Span" by using cursor keys. Then press

Enter

to fix the selection and set each value.

(1) "RAID": Sets RAID level.

Parameter

Remarks

0

RAID0

1

RAID1

10

Striping of RAID1

The selectable RAID level varies depending on the number of hard disk drives
that configure a pack.

(2) "Size": Sets virtual drive size.

Up to 8 virtual drives can be created per RAID Controller.

(3) "DWC": Sets parameter for Disk Write Cache.

Parameter

Remarks

Off

Write through

On *

1

Write back

*1 Recommended setting.

"Write-back On" enables good performance, however, cache data may be lost at
an unexpected power failure. "Write-back Off" reduces performance by
approximately 50%.

(4) "RA": Sets parameter for Read Ahead.

Parameter

Remarks

Off

Does not perform read ahead.

On

Performs read ahead.

«
...
102
103
104
105
106
...
»

Содержание Express5800/110Ge













































































































































































































































































































































Отзывы:

Нет отзывов