Nautel NX300 Скачать руководство пользователя страница 48

Страница: 48 / 162

NX300 Operations and Maintenance Manual

Operating the transmitter

Page 2-30

Issue 3.0 2012-11-01

Use the left and right buttons to make fine adjustments.

Use the up or down button to maximize (if it was minimized) or minimize (if it was maximized) the
panel size.

Use the “peak” button to place the cursor on the next successive peak (moving left to right) in the
spectrum.

Use the “cog” button to gain access to spectrum settings (see

Figure 2.16

) such as:

•

Resolution Bandwidth:

determines the FFT bin size or the smallest frequency that can be

resolved. Set between 90 Hz and 2500 Hz (default is 300 Hz). Decreasing this value provides
better frequency resolution, but will increase the sweep time.

•

Span

: determines the start and stop frequencies of the analyzer with the carrier frequency

always at the center. Set between 20 kHz and 300 kHz (default is 150 kHz).

•

Averages

: determines the number of averages that the analyzer performs per sweep. Set

between 0 and 100 (default is 19).

•

Measurement Source

: determines the source of the spectrum plot (transmitter output,

audio analyzer, etc.) that is being displayed. Selecting

TX Output

uses the exciter’s RF sample

feedback signal to display the RF output spectrum. Selecting

Audio Analyzer

displays the

composite baseband signal.

•

Clear Averaging:

resets the averaged signal shown on the spectrum analyzer.

Figure 2.16: Spectrum Settings

Содержание NX300



































































































































































Результаты поиска

Содержание NX300

Отзывы:

Бренды по названию

Популярные бренды

Nautel NX300, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание NX300

Отзывы:

Бренды по названию

Популярные бренды