manualshive.com logo in svg

Nautel NX300, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Nautel NX300 Скачать руководство пользователя страница 149

NX300 Operations and Maintenance Manual

Routine maintenance

Issue 3.0  2012-11-01

Page 3-1

Section 3:  

Routine maintenance

This section provides instructions for performing routine maintenance on the NX300 transmitter. 
This section includes the following topics: 

•

Scheduled maintenance

•

Replacing a damaged air filter - see page 3-2

•

Performing on-air checks - see page 3-3

•

Replacing the control/interface PWB battery - see page 3-4

•

Inspecting lightning protection systems - see page 3-5

Scheduled maintenance

Scheduled maintenance consists of performing a visual inspection of the NX300 at scheduled 
intervals. The recommended minimum time between scheduled maintenance visits is three months. 
Local operating and environmental conditions may dictate more frequent visits, while in remote sites 
less frequent visits may be acceptable. Experience and system reliability will determine the most 
practical schedule for a specific installation.

Cleaning

At a minimum, follow the cleaning procedures listed below.

1. Clean the air filters, noting there is one in the back of each cabinet. Remove the air filters, 

rinse them with water, spray them with Handi-Koter filter coat (Nautel Part # HQ59, 
located in the ancillary kit), then re-install the air filters. If an air filter becomes damaged, 
replace it as soon as possible. See 

“Replacing a damaged air filter” on page 3-2

.

2. Clean the NX300 using a vacuum cleaner and a soft-bristle brush to remove loose dirt. 

Clean, damp rags should be used to remove dirt that cannot be removed with a vacuum 
cleaner. Never use compressed air to clean the NX300.

Note: 
A site located in a dirty area using open-air cooling requires more extensive cleaning than a site 
located in a clean area using closed-air cooling.

Содержание NX300



































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды