Nature's Comfort GT-220 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 24

Nature's Comfort GT-220 Скачать руководство пользователя страница 22

CB

Built Like A Tank With Laser Precision

Page

22

of 24

Moisture from condensation or rain must not be allowed to accumulate in the firebox, refractory
channel, heat exchanger, or ash pan during the off-season. Failure to perform preventive
maintenance may result in severe corrosion and major damage to the boiler. This is NOT covered
under warranty.

VI. Disclaimer

All installation and operation must follow Federal, Provincial, State and Local codes,
ordinances and laws.

Nature’s Comfort boilers are not intended to be used in urban areas.

Nature’s Comfort boilers are not intended to be the only source of heat. A backup system
should always be in place and ready for use.

Nature’s Comfort boilers are not intended to and must not operate under pressure.

All electrical and plumbing should be done by qualified personnel and conform to national,
state and local electrical, plumbing, fire and building codes.

Manufacturer is not liable for damages to personnel or property for misuse, improper
installation of equipment or for knowing Federal, Provincial, State and Local codes, ordinances
and laws including local installation codes. Owner assumes all responsibility for this.

GOING AWAY

When going away during freezing weather and no one will be keeping the boiler going, turn your
backup heat system on, the boiler control switch off and keep the circulation pump running. Your
boiler will now operate in reverse heat being kept above freezing by your backup system
eliminating the need to otherwise drain the boiler.

Please keep this manual with all other important papers. The information in this manual is
necessary for the installation, operation and proper use of your boiler. If you should ever have a
problem or question refer to this manual or call your dealer. Please have your serial number
ready. This is found on a label on the back of the rear access door or stamped into the firebox
door jamb on the top left. If your dealer does not have the information you need, request they
contact Nature’s Comfort and your dealer will be further educated to provide the best possible
customer service.

«
...
20
21
22
23
24
»

Содержание GT-220

























Отзывы:

Нет отзывов