National PANTHER 5110 Скачать руководство пользователя страница 73

Страница: 73 / 83

Page 60

5110 ACCESSORIES

STRAIGHT SHANK BLADES

The ultimate for tough removals. Works well for ceramic, wood and thick epoxy.

7070-2

2'' STRAIGHT SHANK BLADE

7070-3

3'' STRAIGHT SHANK BLADE

7070-4

4'' STRAIGHT SHANK BLADE

7070-6

6'' STRAIGHT SHANK BLADE

7071-2

2'' ANGLE SHANK BLADE

7071-3

3'' ANGLE SHANK BLADE

7071-4

4'' ANGLE SHANK BLADE

7071-6

6'' ANGLE SHANK BLADE

ANGLE SHANK/SHOE BLADES

The same application as the #7070 blades, but is mounted at an angle to achieve the optimum shear
point for optimum performance. Works well for ceramic and thick epoxy.

7072-2

2'' STRAIGHT SHANK WITH CARBIDE TIP BLADE

7072-3

3'' STRAIGHT SHANK WITH CARBIDE TIP BLADE

7072-4

4'' STRAIGHT SHANK WITH CARBIDE TIP BLADE

7072-6

6'' STRAIGHT SHANK WITH CARBIDE TIP BLADE

STRAIGHT SHANK WITH CARBIDE TIPS

The same application as the #7070 blades, but are carbide tipped for holding a sharp edge for long
periods. Works well for ceramic and thick epoxy.

7079-2

2'' EXTRA HD CERAMIC EPOXY SHANK WITH CARBIDE TIP

7079-4

4'' EXTRA HD CERAMIC EPOXY SHANK WITH CARBIDE TIP

7079-6

6'' EXTRA HD CERAMIC EPOXY SHANK WITH CARBIDE TIP

EXTRA HEAVY DUTY CERAMIC EPOXY SHANKS WITH CARBIDE TIP

Designed for ceramic removal and thin-set rescraping. 1/2

of carbide which is twice the carbide of the

#7072 & #7073 series blades. The extra carbide allows for maximum resharpening. Strong enough to
work on machines up to 3500 lbs.

Содержание PANTHER 5110




















































































Результаты поиска

Содержание PANTHER 5110

Отзывы:

Бренды по названию

Популярные бренды

National PANTHER 5110, Инструкция по эксплуатации

Результаты поиска

Содержание PANTHER 5110

Отзывы:

Бренды по названию

Популярные бренды