National Semiconductor LMX9838 Скачать руководство пользователя страница 21

Страница: 21 / 30

TABLE 23. Local Bluetooth Settings

Command

Event

Description

Read Local Name

Read Local Name Confirm

Read actual friendly name of the device

Write Local Name

Write Local Name Confirm

Set the friendly name of the device

Read Local BDADDR

Read Local BDADDR Confirm

Change Local BDADDR

Change Local BDADDR Confirm Note: The BDADDR is programmed by NSC. It can not be retrieved if

erased!

Store Class of Device

Store Class of Device Confirm

Set Scan Mode

Set Scan Mode Confirm

Change mode for discoverability and connectability

Set Scan Mode Indication

Reports end of Automatic limited discoverable mode

Get Fixed Pin

Get Fixed Pin Confirm

Reads current PinCode stored within the device

Set Fixed Pin

Set Fixed Pin Confirm

Set the local PinCode

PIN request

a PIN code is requested during authentication of an ACL link

Get Security Mode

Get Security Mode Confirm

Get actual Security mode

Set Security Mode

Set Security Mode Confirm

Configure Security mode for local device (default 2)

Remove Pairing

Remove Pairing Confirm

Remove pairing with a remote device

List Paired Devices

List of Paired Devices

Get list of paired devices stored in the LMX9838 data memory

Set Default Link Timeout Set Default Link Timeout Confirm Store default link supervision timeout

Get Default Link Timeout Get Default Link Timeout Confirm Get stored default link supervision timeout

Force Master Role

Force Master Role Confirm

Enables/Disables the request for master role at incoming connections

TABLE 24. Local Service Database Configuration

Command

Event

Description

Store generic SDP Record

Store SDP Record Confirm

Create a new service record within the service database

Enable SDP Record

Enable SDP Record Confirm

Enable or disable SDP records

Delete All SDP Records

Delete All SDP Records Confirm

Ports to Open

Ports to Open Confirmed

Specify the RFComm Ports to open on startup

TABLE 25. Local Hardware Commends

Command

Event

Description

Set Default Audio Settings

Set Default Audio Settings Confirm

Configure Default Settings for Audio Codec and Air Format,
stored in NVS

Get Default Audio Settings

Get Default Audio Settings Confirm

Get stored Default Audio Settings

Set Event Filter

Set Event Filter Confirm

Configures the reporting level of the command interface

Get Event Filter

Get Event Filter Confirm

Get the status of the reporting level

Read RSSI

Read RSSI Confirm

Returns an indicator for the incoming signal strength

Change UART Speed

Change UART Speed Confirm

Set specific UART speed; needs proper ISEL pin setting

Change UART Settings

Change UART Settings Confirm

Change configuration for parity and stop bits

Test Mode

Test Mode Confirm

Enable Bluetooth, EMI test, or local loopback

Restore Factory Settings

Restore Factory Settings Confirm

Reset

Dongle Ready

Soft reset

Firmware Upgrade

Stops the bluetooth firmware and executes the In-system-
programming code

Set Clock Frequency

Set Clock Frequency Confirm

Write Clock Frequency setting in the NVS

Get Clock Frequency

Get Clock Frequency Confirm

Read Clock Frequency setting from the NVS

Set PCM Slave Configuration Set PCM Slave Configuration Confirm Write the PCM Slave Configuration in the NVS

Write ROM Patch

Write ROM Patch Confirm

Store ROM Patch in the Simply Blue module

Read Memory

Read Memory Confirm

Read from the internal RAM

Write Memory

Write Memory Confirm

Write to the internal RAM

www.national.com

LMX9838

Содержание LMX9838































Результаты поиска

Содержание LMX9838

Отзывы:

Похожие инструкции для LMX9838

Бренды по названию

Популярные бренды

National Semiconductor LMX9838, Руководство пользователя

Результаты поиска

Содержание LMX9838

Отзывы:

Похожие инструкции для LMX9838

Бренды по названию

Популярные бренды