National Semiconductor LMX9838 Скачать руководство пользователя страница 20

Страница: 20 / 30

TABLE 19. Bluetooth Low Power Modes

Command

Event

Description

Set Default Link Policy

Set Default Link Policy Confirm

Defines the link policy used for any incoming or outgoing link

Get Default Link Policy

Get Default Link Policy Confirm

Returns the stored default link policy

Set Link Policy

Set Link Policy Confirm

Defines the modes allowed for a specific link

Get Link Policy

Get Link Policy Confirm

Returns the actual link policy for the link

Enter Sniff Mode

Enter Sniff Mode Confirm

Exit Sniff Mode

Exit Sniff Mode Confirm

Enter Hold Mode

Enter Hold Mode Confirm

Power Save Mode Changed

Remote device changed power save mode on the link

TABLE 20. Audio Control Commands

Command

Event

Description

Establish SCO Link

Establish SCO Link Confirm

Establish SCO Link on existing RFComm Link

SCO Link Established Indicator

A remote device has established a SCO link to the local
device

Release SCO Link

Release SCO Link Confirm

Release SCO Link Audio Control

SCO Link Released Indicator

SCO Link has been released

Change SCO Packet Type

Change SCO Packet Type Confirm

Changes Packet Type for existing SCO link

SCO Packet Type changed indicator

SCO Packet Type has been changed

Set Audio Settings

Set Audio Settings Confirm

Set Audio Settings for existing Link

Get Audio Settings

Get Audio Settings Confirm

Get Audio Settings for existing Link

Set Volume

Set Volume Confirm

Configure the volume

Get Volume

Get Volume Confirm

Get current volume setting

Mute

Mute Confirm

Mutes the microphone input

TABLE 21. Wake Up Functionality

Command

Event

Description

Disable Transport Layer

Transport Layer Enabled

Disabling the UART Transport Layer and activates the
Hardware Wakeup function

TABLE 22. SPP Port Configuration and Status

Command

Event

Description

Set Port Config

Set Port Config Confirm

Set port setting for the virtual serial port link over the air

Get Port Config

Get Port Config Confirm

Read the actual port settings for a virtual serial port

Port Config Changed

Notification if port settings were changed from remote device

SPP Get Port Status

SPP Get Port Status Confirm

Returns status of DTR, RTS (for the active RFComm link)

SPP Port Set DTR

SPP Port Set DTR Confirm

Sets the DTR bit on the specified link

SPP Port Set RTS

SPP Port Set RTS Confirm

Sets the RTS bit on the specified link

SPP Port BREAK

Indicates that the host has detected a break

SPP Port Overrun Error

SPP Port Overrun Error Confirm

Used to indicate that the host has detected an overrun error

SPP Port Parity Error

SPP Port Parity Error Confirm

Host has detected a parity error

SPP Port Framing Error

SPP Port Framing Error Confirm

Host has detected a framing error

SPP Port Status Changed

Indicates that remote device has changed one of the port
status bits

www.national.com

LMX9838

Содержание LMX9838































Результаты поиска

Содержание LMX9838

Отзывы:

Похожие инструкции для LMX9838

Бренды по названию

Популярные бренды

National Semiconductor LMX9838, Руководство пользователя

Результаты поиска

Содержание LMX9838

Отзывы:

Похожие инструкции для LMX9838

Бренды по названию

Популярные бренды