National Instruments Fieldpoint CFP-2200 Скачать руководство пользователя | Manualshive

Страница: 25 / 38

background image

©

National Instruments Corporation

25

cFP-2200/2210/2220

Configuring DIP Switches

Figure 29.

DIP Switches

All of the DIP switches are in the OFF position when the controller is
shipped from National Instruments.

IP RESET Switch

Push the IP RESET switch to the ON position and reboot the controller to
reset the IP address to

0.0.0.0

. If the controller is on your local subnet and

the IP RESET switch is in the ON position, the controller appears in MAX
with IP address

0.0.0.0

. You can configure a new IP address for the

controller in MAX. Refer to the

Resetting the Network Configuration of the

section for more information about resetting the IP address. You

also can push this switch to the ON position to unlock a controller that was
previously locked in MAX.

SAFE MODE Switch

The position of the SAFE MODE switch determines whether the embedded
LabVIEW Real-Time engine launches at startup. If the switch is in the OFF
position, the LabVIEW Real-Time engine launches. Keep this switch in the
OFF position during normal operation. If the switch is in the ON position
at startup, the cFP-22

xx

launches only the essential services required

for updating its configuration and installing software. The LabVIEW
Real-Time engine does not launch.

Push the SAFE MODE switch to the ON position if the software on the
controller is corrupted. Even if the switch is not in the ON position, the
controller automatically boots into safe mode if there is no software
installed on it. The SAFE MODE switch must be in the ON position to
reformat the drive on the controller. Refer to the

Measurement &

Automation Explorer Help

for more about installing software and

reformatting the drive.

IP RESET

SAFE MODE

NO APP

CONS. OUT

USER2

USER1

«
...
23
24
25
26
27
...
»

Содержание Fieldpoint CFP-2200







































Отзывы:

Нет отзывов

Похожие инструкции для Fieldpoint CFP-2200

Бренд: Balboa Instruments Страницы: 10

Бренд: Quantum Data Страницы: 36

Бренд: DAVIS Страницы: 8

Бренд: Ohsung Electronics Страницы: 18

Бренд: Parker Страницы: 44

Бренд: OBaby Страницы: 7

Бренд: V2 ELETTRONICA Страницы: 72

Бренд: Ziton Страницы: 36

Бренд: B&G Страницы: 19

Бренд: ZKTeco Страницы: 13

Бренд: UniPi Technology Страницы: 4

EP Series Pro-Bloc

Бренд: Parker Страницы: 11

Бренд: Parker Страницы: 22

Бренд: Parker Страницы: 2

Бренд: Parker Страницы: 42

Бренд: Belimo Страницы: 2

Бренд: Watts Страницы: 12

Бренд: McIntosh Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды