National Instruments Fieldpoint CFP-2200 Скачать руководство пользователя | Manualshive

Страница: 27 / 38

background image

©

National Instruments Corporation

27

cFP-2200/2210/2220

Using the Reset Button

Pressing the Reset button resets the processor in the same manner as
cycling power.

Understanding LED Indications

Figure 30.

LEDs

STATUS LED

The STATUS LED is off during normal operation. The cFP-22

xx

indicates

specific error conditions by flashing the STATUS LED a certain number of
times as shown in Table 3.

Table 3.

Status LED Indications

Number of Flashes

Indication

1

The controller is unconfigured. Refer to the

Measurement & Automation

Explorer Help

for information about configuring the controller in MAX.

2

The controller

has detected an error in its software. This can occur

when an attempt to upgrade the software is interrupted. Refer to the

Measurement & Automation Explorer Help

for information about

reinstalling software on the controller.

3

The controller is in safe mode. Refer to the

Configuring DIP Switches

section for information about the Safe Mode DIP switch.

4

The software has crashed twice without rebooting or cycling power
between crashes. This usually occurs when the controller runs out of
memory. Review your RT VI and check the memory usage. Modify
the VI as necessary to solve the memory usage issue.

Solid

The controller has detected an unrecoverable error. Please contact
National Instruments.

«
...
25
26
27
28
29
...
»

Содержание Fieldpoint CFP-2200







































Отзывы:

Нет отзывов

Похожие инструкции для Fieldpoint CFP-2200

C-NaviGator III

Бренд: C-Nav Страницы: 20

SIGMA CONTROL 2

Бренд: KAESER KOMPRESSOREN Страницы: 246

Бренд: Lakeshore Страницы: 186

Бренд: PACH & COMPANY Страницы: 4

Бренд: Watlow Страницы: 4

Бренд: Zamel Страницы: 23

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Zander Aachen Страницы: 44

Extra Free ROB-01/12-24V

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 14

Бренд: IBM Страницы: 20

Бренд: DAV TECH Страницы: 24

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 16

Бренд: Daikin Страницы: 46

Бренд: Daikin Страницы: 26

Бренд: MaintTech Страницы: 28

Бренд: Harman Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды