National Instruments Fieldpoint CFP-2200 Скачать руководство пользователя | Manualshive

Страница: 13 / 38

background image

©

National Instruments Corporation

13

cFP-2200/2210/2220

Installing the cFP-22

xx

on the Backplane

1.

Make sure that no power is connected to the controller.

2.

Make sure that the controller is right side up with the NI logo at the top,
and align the captive screws on the controller with the holes on the
backplane.

3.

Seat the card edge at the back of the controller in the card-edge
connector on the backplane.

4.

Press the controller firmly to seat it on the backplane.

Figure 19.

Installing the Controller on the Backplane

5.

Using a number 2 Phillips screwdriver with a shank of at least 64 mm
(2.5 in.) length, tighten the captive screws to 1.1 N · m (10 lb · in.) of
torque.

«
...
11
12
13
14
15
...
»

Содержание Fieldpoint CFP-2200







































Отзывы:

Нет отзывов

Похожие инструкции для Fieldpoint CFP-2200

Бренд: NCR Страницы: 6

TLE Scalable 150

Бренд: GE Страницы: 6

Бренд: GE Страницы: 3

Бренд: GE Страницы: 80

PACSystems* RX3i

Бренд: GE Страницы: 39

PACSystems* RX3i

Бренд: GE Страницы: 35

PACSystems* RX3i

Бренд: GE Страницы: 3

PACSystems* RX3i

Бренд: GE Страницы: 169

PACSystems RX7i

Бренд: GE Страницы: 317

Бренд: BEIER-Electronic Страницы: 22

Бренд: jablotron Страницы: 22

Бренд: jablotron Страницы: 2

Бренд: M-Audio Страницы: 26

Бренд: M Climate Страницы: 12

Бренд: Mamas & Papas Страницы: 44

Бренд: Mamas & Papas Страницы: 8

Бренд: Omegalink Страницы: 2

Бренд: MamaLove Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды