manualshive.com logo in svg

National Instruments AT-GPIB/TNT, Начало работы, Страница: 5 / 64

Поделиться
Скачать
National Instruments AT-GPIB/TNT Скачать руководство пользователя страница 5

 

 

 

FCC/DOC Radio Frequency Interference 
Class B Compliance

This equipment generates and uses radio frequency energy and, if not installed and used in strict 
accordance with the instructions in this manual, may cause interference to radio and television 
reception. Classification requirements are the same for the Federal Communications Commission 
(FCC) and the Canadian Department of Communications (DOC). This equipment has been tested and 
found to comply with the following two regulatory agencies:

Federal Communications Commission

This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. This equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that interference will not occur 
in a particular installation. If this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and on, the user is encouraged to try 
to correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected.

•

Consult the dealer or an experienced radio/TV technician for help.

Notices to User:

Changes or modifications not expressly approved by National Instruments could void 
the user’s authority to operate the equipment under the FCC Rules.

This device complies with the FCC rules only if used with shielded interface cables of 
suitable quality and construction. National Instruments used such cables to test this 
device and provides them for sale to the user. The use of inferior or nonshielded 
interface cables could void the user’s authority to operate the equipment under the 
FCC rules.

If necessary, consult National Instruments or an experienced radio/television technician for additional 
suggestions. The following booklet prepared by the FCC may also be helpful: Interference to Home 
Electronic Entertainment Equipment Handbook. This booklet is available from the U.S. Government 
Printing Office, Washington, DC 20402.

Canadian Department of Communications

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment 
Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel 
brouilleur du Canada.

Содержание AT-GPIB/TNT

































































Отзывы:

Нет отзывов