National Instruments AT-GPIB/TNT Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 64

National Instruments AT-GPIB/TNT Скачать руководство пользователя страница 31

Chapter 2

Installation and Configuration

AT-GPIB/TNT for Windows 98/95

2-14

©

National Instruments Corporation

Figure 2-11. AT-GPIB/TNT Ground Configuration Jumper Settings

3. Record the jumper setting on the

Hardware and Software

Configuration Form

Customer Communication

.

Now that you have properly configured the hardware, continue to the
Install the AT-GPIB/TNT section for installation instructions.

Install the AT-GPIB/TNT

Complete the following steps to install the AT-GPIB/TNT board:

1. Shut down Windows and turn off your computer. Keep the

computer plugged in so that it remains grounded while you install
the GPIB hardware.

2. Remove the top cover (or other access panels) to give yourself

access to the computer expansion slots.

3. Find an unused expansion slot in your computer. The

AT-GPIB/TNT requires a 16-bit ISA expansion slot.

4. Remove the corresponding slot cover on the back panel of the

computer.

5. Insert the AT-GPIB/TNT into the slot with the GPIB connector

sticking out of the opening on the back panel, as shown in
Figure 2-12. It might be a tight fit, but do not force the board into
place.

a. Logic Ground Connected to Shield Ground (Default)

b. Logic Ground Disconnected from Shield Ground

W5

W5

«
...
29
30
31
32
33
...
»

Содержание AT-GPIB/TNT

































































Отзывы:

Нет отзывов