NatComm DS2 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 24

NatComm DS2 Скачать руководство пользователя страница 20

Page 20

Natcomm

PROGRAMMING PROCEDURE

1.

TURN OFF POWER TO YOUR UNIT

2.

SWITCH ON POWER AND PRESS #

(use a Telephone connected to DS2)

3.

YOUR UNIT WILL OUTPUT 3 SHORT ‘BEEPS’

(you are in Program Mode)

If you do not hear 3 beeps, return to the start (1).

4.

ENTER ANY PROGRAMMING COMMANDS AS FOLLOWS

:

(Note - You can change one or more parameters in any order)

A.

NUMBER OF RINGS

To enter the NUMBER OF RINGS press #1xx where xx = number of
rings and can be 01-99 (for example, press #115 for 15 rings)

B.

DOOR PHONE CALL ADVICE TONES

To disable TONES press #40 To enable TONES press #41

C.

LOCK TIME SET UP

To enter the LOCK 1 OPEN TIME press #6xx

xx = time limit in seconds that LOCK 1 will remain open after pressing **.
It can be set from 01-99 (seconds)

(for example, press #630 for 30 seconds)

D.

RESET TO FACTORY DEFAULT SETTINGS

To RESET to Factory Defaults, press

13579

TO EXIT PROGRAMMING MODE - HANG UP.

ALL ENTRIES ARE SAVED IN PERMANENT MEMORY.

«
...
18
19
20
21
22
...
»

Содержание DS2

























Отзывы:

Нет отзывов