Narex EPK 16 D, Оригинальное руководство по эксплуатации

Страница: 17 / 40

English
17
Work instructions
Fix the workpiece onto a solid base.
Excessive movement reduces the performance of the tool significantly,
and shortens the service life of the circular-saw blade and the engine. Use
sharpened circular-saw blades that are suitable for the respective material.
A tiny layer of oil on the saw blade prevents it from corrosion.
Clean the circular-saw blade straight after work, since the residues of glue
and resin deteriorate the quality of the cut.
Cutting of plastics
During cutting plastics, long spiral chippings originate. Electrostatic
charge effect might cause clogging of the hole for outlet of chippings (3)
and blocking the swiveling cover.
Plastic workpieces must adjoin well to the base. Incise carefully and work
fluently, without interruptions. Like this the saw teeth will not stick up and
the section will be smooth.
Maintenance
‰ When replacing the circular-saw blade, make sure to clear the inside
of the cover off accumulated wood dust.
‰ The vents of the engine guard must not get clogged.
‰ The cable can only be replaced in an authorized electrotechnical
workshop which has the licence to carry out this type of work.
After about 200 hours of operation, the following works have to be done:
‰ The length of the brushes must be checked. Brushes shorter than
5 mm have to be replaced with new ones.
‰ Exchange of lubricant grease in the gearbox and in bearings.
To maintain the protection class, the saw has to be checked in terms of
safety, and therefore these works have to be carried out in a specialized
electrotechnical workshop which is authorized for this type of work.
Storage
Packed appliance may be stored in dry, unheated storage place with tem-
perature not lower than –5° C.
Unpacked appliance should be stored only in dry storage place with tem-
perature not lower than +5° C with exclusion of all sudden temperature
changes.
Environmental protection
Power tools, accessories and packaging should be sorted for environmen-
tal-friendly recycling.
Only for EU countries:
Do not dispose of power tools into household waste!
According to the European Directive 2002/96/EC on waste electrical and
electronic equipment and its incorporation into national law, power tools
that are no longer suitable for must be separately collected and sent for
recovery in an environmental-friendly manner.
Warranty
Our equipment is under warranty for at least 12 months with regard to
material or production faults in accordance with national legislation. In the
EU countries, the warranty period for exclusively private use is 24 months
(an invoice or delivery note is required as proof of purchase).
Damage resulting from, in particular, normal wear and tear, overloading,
improper handling, or caused by the user or other damage caused by not
following the operating instructions, or any fault acknowledged at the
time of purchase, is not covered by the warranty.
Complaints will only be acknowledged if the equipment has not been dis-
mantled before being sent back to the suppliers or to an authorised NAR-
EX customer support workshop. Store the operating instructions, safety
notes, spare parts list and proof of purchase in a safe place. In addition, the
manufacturer’s current warranty conditions apply.
Information about noise level and
vibrations
The values have been measured in conformity with EN 60745.
Acoustic pressure level L
pA
= 9588 dB (A).
Acoustic power level L
wA
= 108 dB (A).
In accuracy of measurements K = 3 dB (A).
ATTENTION! Noise is generated during work!
Use ear protection!
Vibration emission value ah (vector sum for three directions) and uncer-
tainty K measured in accordance with EN 60745:
The weighed effective vibration acceleration a
h
value is below 4.4 m/s 2 .
In accuracy of measurements K = 1.5 m/s 2
The emission values specified (vibration, noise) were measured in accord-
ance with the test conditions stipulated in EN 60745 and are intended for
machine comparisons. They are also used for making preliminary esti-
mates regarding vibration and noise loads during operation.
The emission values specified refer to the main applications for which the
power tool is used. If the electric power tool is used for other applications,
with other tools or is not maintained sufficiently prior to operation, how-
ever, the vibration and noise load may be higher when the tool is used.
Take into account any machine idling times and downtimes to estimate
these values more accurately for a specified time period. This may signifi-
cantly reduce the load during the machine operating period.
Certificate of Conformity
We declare that the device meets requirements of the following standards
and directivesc.
Safety:
EN 60745-1; EN 60745-2-5
Directive 2006/42/EC
Electromagnetic compatibility:
EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3
Directive 2004/108/EC
2009
Narex s.r.o.
Chelčického 1932 Antonín Pomeisl
470 01 Česká Lípa CEO of the company
29.12.2009
Changes are reserved