Narex ABU 125-600 B BASIC, Оригинальное руководство по эксплуатации

Страница: 24 / 72

English
24
Charger safety warnings
– This appliance is not designed for use by other people (children
included), physical, sensory or mental incapability or lack of ex-
perience and knowledge of whose prevent from safe use of the
appliance without being supervised, or without being instructed
on use of the appliance by a person responsible for their safety.
– Children should be supervised to avoid their playing with the ap-
pliance.
Information about noise level
and vibrations
The values have been measured in conformity with EN 60745-1.
ABU 125-600 B
Acoustic pressure level L
pA
= 89.1 dB (A).
Acoustic power level L
wA
= 100.1 dB (A).
In accuracy of measurements K = 3.0 dB (A).
ATTENTION! Noise is generated during work!
Use ear protection!
The weighted value of vibrations affecting hands and arms a
h
= 6.38 m.s -
2 .
In accuracy of measurements K = 1.5 m.s -2 .
The emission values specified (vibration, noise) were measured in ac-
cordance with the test conditions stipulated in EN 60745 and are intend-
ed for machine comparisons. They are also used for making preliminary
estimates regarding vibration and noise loads during operation.
The emission values specified refer to the main applications for which
the power tool is used. If the electric power tool is used for other ap-
plications, with other tools or is not maintained sufficiently prior to
operation, however, the vibration and noise load may be higher when
the tool is used.
Take into account any machine idling times and downtimes to estimate
these values more accurately for a specified time period. This may signif-
icantly reduce the load during the machine operating period.
Double insulation
To ensure maximum safety of the user our tools are designed and built
to satisfy applicable European standards (EN standards). Tools with
double insulation are marked by the international symbol of a double
square. These tools must not be grounded and a two-wire cable is suffi-
cient to supply them with power. Tools are shielded in accordance with
EN 55014.
Use
The machine is designed for cutting, roughing and brushing metal and
construction materials without the use of water. When cutting construc-
tion material, ensure sufficient dust extraction and always clean the ma-
chine after work (cleaning with compressed air recommended).
The user bears full responsibility for the consequences of using the ma-
chine for purposes it was not designed for.
Accumulator Battery Charge
Instructions
1. Please make sure that the mains voltage is the same as the voltage
listed on the machine plate on the charger. First, plug the power
cable (16b) into the charger (16a), then connect the charger (16a)
to power supply. A red LED indicator (17) will light up. This means
that the charger is ready to charge. Check the connection to power
supply if the red LED indicator does not light up. If power supply
is in order, bring the charger in for repair to an authorised service
centre!
2. Slide the battery (1) into the charger all the way.
3. The red LED indicator light turns off and a green LED indicator
light (17) begins blinking, indicating that the battery is in fast
charge mode.
4. The battery is fully charged after about 60 to 80 minutes (depend-
ing on the battery capacity) once the green LED indicator light
stops blinking and remains lit.
5. Disconnect the battery from the charger. If you do not wish to
charge another battery, disconnect the charger from the power
source.
An overview of charging LED indicator lights (17):
Green LED indicator Red LED indicator Signal combinations
Is off Is on (constant light) Connected to power*
Is on and is blinking Is off The battery is charging
Is on (constant light) Is off The battery is charged
Is on and is blinking Is on and is blinking
The temperature of the
charger or the battery is
too high
Is off Is on and is blinking The battery is damaged
* When the charger is activated after it is connected to power, the red and the
green LED indicator lights will blink for about 1 second, then the red LED indica‑
tor light will stop blinking and remain on (constant light).
New batteries:
Battery capacity may be slightly smaller than the listed value during the
first few initial charge cycles. The reason is that the chemical composi-
tion of the batteries has not been activated yet. This is a temporary issue
and will resolve on its own after a few charge cycles.
Note:
• A blinking green indicator means that the battery is fully charged or
that it is in slow charge mode, which maintains a low charge level of
the battery.
• The initial battery charge may take longer thAN 60 to 80 minutes
(according to battery capacity) depending on the environment
temperature, the power supply and the current charge level.
• If you are not using the charger, please unplug it from the power
source.
Important information about the charging
process:
1. To get the best out of the batteries in terms of longevity and per-
formance is to charge them at an ambient temperature of 18 °C
to 24 °C.
DO NOT CHARGE
the batteries at temperatures below
0 °C and above 45 °C. This is very important. You will prevent serious
battery damage.
• Do not charge the batteries in direct sunlight, especially in the sum-
mer! You will prevent extreme overheating, which could damage
them!
2. If a battery that is too cold (below 0 °C) is inserted into the charg-
er, the charger will not begin charging it right away; instead, the
green and the red indicator light will begin blinking. Once the bat-
tery reaches the right temperature naturally (within the standard
range), the fast charge process will begin automatically.
• If a battery that is too hot (more than 45 °C), is inserted into the
charger, the charger will not begin charging it right away; instead,
the green and the red indicator light will begin blinking. Once the
battery reaches the right temperature (within the standard range),
the fast charge process will begin automatically.
3. If it is not possible to charge the batteries properly (the red indica-
tor is blinking):
• Check that the battery contact surfaces are not dirty. Clean them
with a cotton wad and alcohol as needed.
• If the battery is still not charging properly, send or bring the charger
(including the batteries) to your nearest authorised service centre.
4. Under certain conditions and if the charger is connected to power,
foreign material may short circuit the charge contacts inside the
charger. Foreign conducting substances, such as steel fibres, alu-
minium foils or metal deposits must be removed from the charger
continuously. Always unplug the charger from power prior to clean-
ing.
5. If you are carrying out several different charge operations one after
the other, the charger may become hot. This is normal and is not
a sign of a technical problem.
6. Prevent liquid from getting inside the charger as it could cause an
electrical injury. Do not place the battery in a hot environment if
you wish to facilitate the battery cool down process.
7. Accumulator batteries can remain plugged into the charger with-
out a risk of damage to them or the charger itself. The batteries
will remain fully charged in the charger. DO NOT LEAVE charged
batteries in the charger if the charger is not plugged into the power
outlet.
8. DO NOT USE ACCUMULATOR BATTERIES if they are damaged or if
liquid leaks out of the cells. If the battery liquid comes into contact
with your skin, immediately flush the area with water and monitor
the skin’s reaction. Seek medical attention if needed. If it comes into