background image

 

 

GAS-FIRED INFRARED   

OUTDOOR PATIO HEATER   

              

INSTALLATION, OPERATION 

           

MAINTENANCE INSTRUCTIONS 

 

 

 

 
 
 
 
                                   ®                     ®    
 

FOR MODEL PTH-103-3G   

 

TABLE OF CONTENTS

                                                   

PAGE 

IMPORTANT …………………………………………………………………… 

 

  1 

TOOLS & PARTS ……………………………………………………………….. 

 

  2   

PRECAUTIONS………………………………………………………………….. 

 

  3       

ASSEMBLY INSTRUCTIONS …………………………………………………. 

 

  4     

GAS REQUIREMENTS & LEAK TESTING ………………………………….. 

 

  9   

SAFETY CHECKS ……………………………………………………………….   

  10   

LOCATING HEATER FOR USE ………………………………………………. 

 

  11 

LIGHTING / SHUTDOWN ……………………………………………………….       12   
STORAGE / BURNER REMOVAL………………………………..…………….   

  14 

BURNER INSTALLATION / PILOT CLEANING ………………………………       15 
BURNER REMOVAL …………………………………………………………….   

  16   

TROUBLE SHOOTING .…………………………………………………………   

  17 

PARTS LIST ………………………………………………………………………       18 
WARRANTY ………………………………………………………………………       19 

 

READ THE FOLLOWING INSTRUCTIONS CAREFULLY AND BE SURE YOUR PATIO HEATER IS 
PROPERLY INSTALLED, ASSEMBLIED AND CARED FOR. FAILURE TO FOLLOW THESE 
INSTRUCTIONS MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. IF 
YOU HAVE QUESTIONS CONCERNING ASSEMBLY OR OPERATION, CONSULT YOUR 
DEALER, GAS APPLIANCE SERVICE REPRESENTATIVE OR YOUR GAS COMPANY. 

 

NOTE TO INSTALLER:   
LEAVE THESE INSTRUCTIONS WITH THE CONSUMER AFTER INSTALLATION.   

 

NOTE TO THE CONSUMER:   
RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.   

 

 

Содержание PTH-103-3G






















Отзывы: