manualshive.com logo in svg

Napoleon Madison GD80NT, Инструкция по установке и эксплуатации

Поделиться
Скачать
Napoleon Madison GD80NT Скачать руководство пользователя страница 16

16

W415-0695 / 05.12.08

FIGURE 24

The vent system must be supported approximately every 3 feet for both vertical and horizontal runs. Use Wolf Steel support 
ring assembly or equivalent noncombustible strapping to maintain the minimum clearance to combustibles for both vertical 
and horizontal runs. 

All inner exhaust and outer intake vent pipe joists may be sealed using either red high temperature silicone sealant  
W573-0002  or black high temperature Mill Pac W573-0007 with the exception of  the fireplace exhaust flue collar 
which must be sealed using Mill Pac (not supplied).

FIGURE 25

USING RIGID VENT COMPONENTS

HORIZONTAL AIR TERMINAL INSTALLATION

FIGURE 26

VERTICAL VENTING INSTALLATION

FIGURE 27

1. 

Move the fi replace into position.

2. 

Fasten the roof support to the roof using the screws provided. The roof support is optional. In 

this case the venting is to be adequately supported using either an alternate method suitable to 
the authority having jurisdiction or the optional roof support. 

3.

 Apply high temperature sealant W573-0002 (not supplied) to the outer edge of the inner 

sleeve of the air terminal. Slip a 5” diameter coupler a minimum of 2” over the sleeve and 
secure using 3 screws. 

4

.

 Apply high temperature sealant W573-0002 (not supplied) to the outer edge of the of the outside sleeve of 

the air terminal. Slip a 8” diameter coupler over the sleeve and secure as before. Trim the 8” coupler even with 
the 5” coupler end.

5.

 Thread the air terminal pipe assembly down through the roof  support and attach, ensuring that a minimum 16” 

of air terminal will penetrate the roof when fastened. 

If the attic space is tight, we recommend threading the 

Wolf Steel vent pipe collar or equivalent loosely onto the air terminal assembly as it is passed through 
the attic. 

The air terminal must be located vertically and plumb. 

6.

 Remove nails from the shingles, above and to the sides of the chimney. Place the fl ashing over the air terminal 

and slide it underneath the sides and upper edge of the shingles. Ensure that the air terminal is properly centred 
within the fl ashing, giving a 3/4” margin all around. Fasten to the roof. Do NOT nail through the lower portion of the fl ashing. Make 
weather-tight by sealing with caulking. Where possible, cover the sides and top edges of the fl ashing with roofi ng material. 

EXTENDED HORIZONTAL AIR TERMINAL INSTALLATION

1. 

Move the fi replace into position. Measure the vent length 

required between terminal and fi replace taking into account 
the additional length needed for the fi nished wall surface and 
any 1¼” overlaps between venting components.

2. 

Apply high temperature sealant W573-0007 (not sup-

plied) to the outer edge of the 5” inner collar of the fi replace.  
Attach the fi rst vent component and secure using 3 self tap-
ping screws. Repeat using 8” piping.  

3. 

Holding the air terminal insert the terminal into both vent 

pipes with a twisting motion to ensure that both the terminal 
sleeves engage into the vent pipes and sealant. Secure the 
terminal to the exterior wall and make weather tight by sealing 
with caulking (not supplied). 

 

1. 

Follow the instructions for “Horizontal Air Terminal Installations”, items 1 to 3. 

2. 

Continue adding components alternating inner and outer venting. Ensure that all 5” 

venting and elbows have suffi cient vent spacers attached and each  component is securely 
fastened to the one prior. Attach the 5” telescopic sleeve to the vent run. 

Repeat using a 8” telescopic sleeve. Secure and seal as before. To facilitate completion, 
attach 5” and 8” couplers to the air terminal. 

3.

 Install the air terminal. 

See item 3 of the Horizontal Air Terminal Installation.

 Extend the 5” 

telescopic sleeve; connect to the air terminal assembly. Fasten with self tapping screws and seal. 
Repeat using the 8” telescopic sleeve.

Содержание Madison GD80NT









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды