manualshive.com logo in svg

NAPCO XP-400, Руководство по установке

Поделиться
Скачать
NAPCO XP-400 Скачать руководство пользователя страница 16

16

WI853C XP-400 Installation Instructions

Pager Alarm data is the same as 4/2 format
with the exception that the 2 digit Report
Code is transmitted before the 4 digit Sub-
scriber ID.

[33]Receiver Options

(1) 2300 Hz HS/Kissoff - Select 2300 Hz
Handshake and Kissoff.

(2) Sumcheck - Only used for the following
Receiver Formats: Ademco Slow, Radionics
Fast, Silent Knight Fast and Universal High
Speed. This is a sophisticated data format
used to enhance the speed and check the
accuracy of the received transmission. This
format should be used whenever the central
station has this capability.  Instead of send-
ing a second round to verify correct data, the
panel sends a Sumcheck digit after sending
the Subscriber ID and Alarm Code.

(3) Single Digit - 3/1 Format.  3-digit Sub-
scriber ID number and a 1-digit Alarm Code
will be transmitted.

(4) No Handshake/Pager Extend

 - The

meaning of this option is dependent on
Receiver Format programming.

No Handshake  (

All receiver formats except

Pager Format)

If programmed no Handshake is re-
quired.

Pager Extend

 

(Pager Format Selected)

Pager PIN Number

  -  Program if a PIN

number is required by the paging sys-
tem. The digits in 

Telephone Number

2 will be added on to telephone num-
ber 1 and/or telephone number 3 al-
lowing for a total of 24 digits.  See

sample program below.  Note: If se-
lected do not program backup report-
ing.
If a 7-digit PIN number is required,
program the panel as follows:

[31] - Pager Telephone number
[32] - Select Pager Format

[33] - Select Pager Extend

[41] - 

D D D X X X X X X X C 0

[34]Zone Report, Telco 1

Select zone(s) required to send an alarm
report to Telephone Number 1.

[35]Zone Restore Report, Telco 1

Select zone(s) required to send a restore
report to Telephone Number 1.  The zones
will send a restore after Bell time-out, unless
programmed as silent zones.

[36]System Reporting, Telco 1

(1) Keypad Panic 2 - Program to activate a

Keypad Panic 2 report (

).

(2) AUX/AMBUSH - Program to activate an

AUX or AMBUSH report (

&&

).

(3) Panic - Program to activate a Panic

report (

'

).

PIN Number

Terminating Digit (#)

 Delay

Leading 0

Pager display will appear as shown in Figure 7
except there will be only one leading 0.

 

Leading Digits

Report Code

Subscriber ID Number

FIGURE

 

7 D

EFAULT 

P

AGER 

D

ISPLAY

Wi853c 
page 16

Tuesday, September 16, 1997 10:42 

Содержание XP-400





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды