IDENTIFICATION OF CONTROLS
REMOTE CONTROL
2
7
8
10
1
3, 4
6
9
5
12
11
USING THE VR 3 REMOTE CONTROL
The VR 3 remote control handset handles the key functions of the VISO THREE. The VR 3 can also be used
to directly command other NAD products that respond to applicable common remote control codes. This
includes other NAD Stereo Receiver, Integrated Amplifier and Preamplifier models. It has additional controls
to remotely operate NAD CD Players, AM/FM Tuners and dedicated AM/FM/DAB Tuners. It will operate up to a
distance of 23ft (7m). Alkaline batteries are recommended for maximum operating life. Two AA batteries should
be fitted in the battery compartment at the rear of the Remote Control handset. When replacing batteries,
check that they have been put in the right way round, as indicated on the base of the battery compartment.
NOTE
The remote control handset supplied with the VISO THREE is of a universal NAD type, designed to
operate several NAD models. Some buttons are applicable only to specific NAD models. Contact
your dealer or NAD audio specialist for assistance.
1 ON, OFF
The VR 3 remote has a separate ON and OFF button.
•
Press the ON button to switch the unit from Standby to operating mode. Press the OFF button
to switch the unit to Standby mode.
2 DEVICE SELECTOR
A Device Selector button determines only what component the VR 3 will command; it does not
perform any function on the VISO THREE.
•
Press desired Device Selector button for the applicable buttons to be directed to a “page” of
commands relevant to the selected device. Upon selecting a Device, you can now press the
corresponding VR 3 control buttons applicable for the selected Device.
3 INPUT SELECTORS
Refer to the corresponding labels printed in the remote control faceplate and their respective
assigned buttons to make use of these functions.
•
Set the DEVICE SELECTOR to “AMP” in order to gain access to these buttons.
•
The input selector buttons perform the same functions as the buttons labeled the same on the
front panel.
4 NUMERIC KEYS
The numeric keys allow for direct input of tracks for CD players and direct channel/preset access for
tuners and receivers.
5 SLEEP
Switch off the NAD Receiver or Tuner after a preset number of minutes.
SLEEP MODE
The Sleep Mode timer will switch the VISO THREE to Standby mode automatically after a preset
number of minutes. Pressing the VR 3’s [SLEEP] button once will display the current setting of the
sleep time mode or remaining time before the VISO THREE goes to standby mode. Pressing the
VR 3’s [SLEEP] button a second time within a 3-second period will change the sleep time mode
to the next sleep time setting. Each consecutive press increases the sleep time in 30-minute
increments from 30 to 90 minutes. To cancel the sleep mode, continue pressing the VR 3’s [SLEEP]
button until “Sleep Off” is displayed on the VFD. Switching the VISO THREE to standby mode from
either the VR 3’s OFF or the VISO THREE’s Standby button will also cancel the sleep mode.
6 MUTE
•
Press the [MUTE] button to temporarily switch OFF the sound to the speakers and headphones.
Press MUTE again to restore sound.
•
MUTE mode is indicated by the Standby LED indicator flashing for NAD Integrated Amplifiers or
“Mute” shown in the VFD of NAD Receivers.
•
Adjusting the volume level via the VR 3 or the front panel volume knob will automatically
release the mute function.
7 DIM
•
Reduce or restore VFD brightness.
•
Depending on the NAD model, the brightness of the front panel display will vary when you
toggle this button.
•
Use with NAD VISO THREE and other compatible NAD Stereo Receiver, Tuner and CD Player
models.
10
EN
G
LIS
H
PO
R
TU
G
U
ÊS
FR
ANÇ
AIS
ESP
AÑOL
IT
ALIANO
DEUT
SCH
NEDERL
ANDS
SVENSK
A
РУ
ССКИЙ
