manualshive.com logo in svg

Nabco GT20, Руководство по проводке и программированию

Поделиться
Скачать
Nabco GT20 Скачать руководство пользователя страница 36

 

36 of 43

 

GT20 Wire and Programming Manual 

www.NabcoEntrances.com

P/N C-00140 

Rev 5-7-18

Do not place finger or uninsulated tools inside the electrical GT20 Control . Touching wires or 

other parts inside the enclosure may cause electrical shock, serious injury or death .

1. Ensure the Power is OFF.
2. Use a T-10 Torx Allen Wrench to remove (4) M3 x 5 Torx Screws used to secure the GT20 Control Board. Set Aside. Figure 4.

a.  The (4) Torx screws are located at (2) corners on the opposite side of the Terminal Strips and (2) middle location on the 

opposite side of the Relay PCB Board Connector Strip. 

3. Insert (4) M3 x 12 Stand Off Torx Screws within each screw hole.
4. Secure the Relay PCB Board onto the GT20 Control with (4) M3 x 5 Torx Screws.
5. Proceed to wire each PCB Terminal accordingly.

SECTION 11 .2: Program the Relay PCB Board

1. Switch-on the Main Power Switch. The Home Page will be displayed.

>##<

        E01

2. Briefly push down on the Joystick. The Menu Selection Page will be displayed. 
3. Move the Joystick to the Right or Left until the Menu CONFIG is displayed.

CONFIG 

4. Briefly push down on the Joystick. An Element Page will be displayed. 
5. Move the Joystick Down until the Element RC 0.1 is displayed.

RC     0.1 

CLOSED

6. Briefly push down on the Joystick. The Value will start to blink on the lower half of the screen. 
7. Move the Joystick to the Right or to the Left to select(1) the appropriate Value.
8. Repeat steps 5 thru 7 until all Relay PCBs are programmed within the GT20 Control.

11 .2 .3 Configuration Menu for Relay PCB Board

RC 0.1

RC 0.2

RC 0.3

RC 0.4

CLOSED

OPEN

ERROR

GONG

Only (1) PCB Terminal per Switch Activation is allowed. For example (2) activations (during closing and 

opening) must be wired to (2) different PCB Terminals.

Note:  The Configurator Menu will only display the following Elements/Values when the Relay PCB 

Board is intalled.

Note:  NABCO does not install more than (1) Relay PCB Board.

CLOSED

Relay switches when the Door Panel is fully closed.

OPENNG

Relay switches when the Door Panel is opening.

OPEN

Relay switches when the Door Panel is fully open.

CLOSING

Relay switches when the Door Panel is closing.

ERROR

Relay switches if the GT20 Control detects an Error(s).

PSAUTO

Relay switches when the Program Selector is in Mode: AUTOMATIC

PSNIGHT

Relay switches when the Program Selector is in Mode: NIGHT

PSEXIT

Relay switches when the Program Selector is in Mode: EXIT

PSOPEN

Relay switches when the Program Selector is in Mode: OPEN

PSMANU

Relay switches when the Program Selector is in Mode: MANUAL

GONG

Relay switches 

momentarily

 during the time the GT20 Control recieves a signal from: Terminal 

12 and Terminal 13 (Opening Command Inside).

LOCKED

Relay switches during the time the Door Panel is LOCKED with an electric lock.

DANGER

Содержание GT20












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды