N-Tron 608MFX-ST Скачать руководство пользователя страница 20

20

N-TRON Limited Warranty

N-TRON, Corp. warrants to the end user that this hardware product will be free
from defects in workmanship and materials, under normal use and service, for
the applicable warranty period from the date of purchase from N-TRON or its
authorized reseller.

If a product does not operate as warranted during the

applicable warranty period, N-TRON shall, at its option and expense, repair the
defective product or part, deliver to customer an equivalent product or part to
replace the defective item, or refund to customer the purchase price paid for the
defective product.  All products that are replaced will become the property of N-
TRON.  Replacement products may be new or reconditioned.  Any replaced or
repaired product or part has a ninety (90) day warranty or the remainder of the
initial warranty period, whichever is longer.  N-TRON shall not be responsible
for any custom software or firmware, configuration information, or memory data
of customer contained in, stored on, or integrated with any products returned to
N-TRON pursuant to any warranty.

OBTAINING WARRANTY SERVICE: Customer must contact N-TRON
within the applicable warranty period to obtain warranty service authorization.
Dated proof of purchase from N-TRON or its authorized reseller may be
required.  Products returned to N-TRON must be pre-authorized by N-TRON
with a Return Material Authorization (RMA) number marked on the outside of
the package, and sent prepaid and packaged appropriately for safe shipment.
Responsibility for loss or damage does not transfer to N-TRON until the
returned item is received by N-TRON.  The repaired or replaced item will be
shipped to the customer, at N-TRON’s expense, not later than thirty (30) days
after N-TRON receives the product.  N-TRON shall not be responsible for any
software, firmware, information, or memory data of customer contained in,
stored on, or integrated with any products returned to N-TRON for repair,
whether under warranty or not.

ADVANCE REPLACEMENT OPTION:  Upon registration, this product
qualifies for advance replacement.  A replacement product will be shipped
within three (3) days after verification by N-TRON that the product is
considered defective.  The shipment of advance replacement products is subject
to local legal requirements and may not be available in all locations.  When an
advance replacement is provided and customer fails to return the original
product to N-TRON within fifteen (15) days after shipment of the replacement,
N-TRON will charge customer for the replacement product, at list price.

WARRANTIES EXCLUSIVE: IF AN N-TRON PRODUCT DOES NOT
OPERATE AS WARRANTED ABOVE, CUSTOMER'S SOLE REMEDY
FOR BREACH OF THAT WARRANTY SHALL BE REPAIR,

Содержание 608MFX-ST























Отзывы: