background image

12

3 - Machine Maintenance

In order to keep the Mytee Lite™ running smoothly and 
reduce the risk of damage to the machine and subsequent 
downtime, Mytee recommends following the maintenance 
schedule below:

Maintenance Item

Daily

Weekly

Clean and inspect tanks.

X

Clean and inspect hoses.

X

Check and clean internal filters.

X

Check power supply cable.

X

Clean machine with all-purpose 
cleaner and cloth.

X

Check spray nozzles.

X

Flush solution system with Mytee 
System Maintainer.

X

Inspect vacuum hoses for holes and 
loose cuffs.

X

Inspect spray pattern for clogging. 
If clogged, remove spray tips and 
soak them in a recommended liquid 
neutralizer for up to six hours. To re-
move spray tip, twist spray tip body 
counter-clockwise.

X

Lubricate wheels with water resis-
tant oil.

X

Inspect machine for water leaks and 
loose hardware.

X

3.1 - Filter Maintenance

The Mytee Lite™ has a small filter on the top of the vac-
uum stack in the recovery tank. This filter should be 
checked and cleaned after each use. 

3.2 - System Maintainer

Regular flushing of the solution system with Mytee Sys-
tem Maintainer keeps your extractor running efficiently by 
removing hard water  scaling that builds up in the system.

How to use System Maintainer:

1.  Thoroughly mix System Maintainer with warm water at a 
1:1 ratio in a separate container. Pour into your Extractor’s 
solution tank.

2.  Connect a cleaning tool (upholstery tool, wand, etc.) and 
remove the jet(s) in order to prevent clogging from dis-
lodged mineral build-up.

3.  Turn on the Extractor’s pump and run the System Main-
tainer solution through the system and into a bucket or 
receptacle until you have a solid stream.

4.  Let sit for about 5 minutes while the System Maintainer 
solution does its job inside your Extractor.

5.  Finish running the rest of the solution through the sys-
tem.

6.  Run clean water through the system to flush out any 
remaining System Maintainer. 

Do not tamper with the set screw on the  
pump pressure switch. This can damage the 
pressure switch.

Содержание 8070 Lite

















Отзывы: