background image

11

LO-LINE RC & LO-LINE RC Heater Cooler

12.0 Troubleshooting

(continued...)

Common Installation Faults

For optimum performance, this unit must be correctly sized to
match the heat loss requirements of the space it is required to

heat, and the heating system must be correctly designed to
provide adequate flow of hot water to the unit (refer to section
2). If the recommendations in section 2 are not followed,
problems may arise as detailed below.

Heating Mode -

No Fan

Heating Mode

(Heater Model only)

poor heating

performance and/or

unit cycles on

water sensor

Possible Causes

Unit switched off

Temperature set point reached

Unit not switched on at fused spur

Fuse blown at fused spur

Unit isolating valves shut

Water temperature reaching fan

convector below 43°C

(Heater model only)

Problem

Remedy

Low water temperature to unit

Turn up boiler thermostat

Poor water flow

Vent air from heating system

Turn on

Increase temperature set point

Switch on at spur

Replace fuse

Open valves

Check boiler -

Programmer ON

Boiler ON and set to high with central

heating pump running

Note:

Operation of fan convector can be checked by

switching to manual fan setting

Heating Mode

(Heater Model only)

poor heating

performance and/or

unit cycles on

water sensor

Possible Causes

Boiler thermostat set too low

Lack of flow to fan convector -

Pump set on low setting

Isolating valves not fully open

System incorrectly balanced with unit starved of hot water flow

Pipe sizing to unit too small

Problem

Poor heating performance

(Heater Model only)

Unit incorrectly sized for heat loss of room

13.0 Maintenance

Before undertaking any maintenance activity isolate the
electrical supply.

Maintenance should be restricted to occasional removal of dust
and lint around the unit. The outer surface may be wiped over

with warm water and mild detergent taking care to avoid water
entering the grille areas.

If the fan convector is still faulty after checking the above, call your installer or MYSON Service.

1

1

.0

1

2

.0

1

3

.0

For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - [email protected] 0844 556 1818   

Содержание LO-LINE RC 14-10













Отзывы: