C B S - 8 8 0 I N S T R U C T I O N M A N U A L
1
Safety Instructions
Below are general safety precautions and warnings that should be
understood prior to setting up or operating your equipment. Read and fully understand all instructions and
warnings prior to using this unit. Your safety is most important! Failure to comply with procedures may result
in serious injury or property damage. Remember:
Unsafe practices or unauthorized modifications could result in accidents or property damage. Failure to follow these
safety rules and take necessary precautions can result in serious injury as well as damage to equipment.
Never operate or service your band sealer until you have read this manual completely and understand it fully.
Plug the band sealer into a standard 120 Volt, 60Hz wall outlet or surge protector. We highly suggest using a
surge protector. Some special order units are 220 Volt, 50Hz. Make adjustments as necessary.
Do not use the band sealer if the power cord, plug or any other parts are damaged. Be sure not to allow the
power cord to drape into your work area. Check that all parts are operating properly and perform the intended
functions. Check for all other conditions that may affect the operation.
Reduce risk of unintentional starting. Make sure the power switch is in the "OFF" position before attaching to
the power source.
Always disconnect sealer from power source before servicing, changing accessories or cleaning the unit.
To provide protection against the risk of electrical shock, the power connection must be properly grounded at all
times.
Do not leave the sealer unattended when in use. Disconnect the sealer from the power source before leaving the
work area.
Band sealer is used solely for sealing thermoplastic materials. Using the machine for any other purpose can cause
damage to the machine and operator. Do NOT use the machine for any other purpose other than to seal
thermoplastic materials. Doing so may result in damage to the machine and injury to the operator.
Always operate machine on a flat stable surface.
While operating machinery, wear close-fitting clothing and tie back long hair to prevent any external items from
getting caught in the machine. Do not wear jewelry when operating the band sealer.
Содержание SealerSales CBS-880I
