31
M1.2.TPT820.NLFREN 21112017
EN
4 Assembly
Following the assembly directions below, you will assemble the plate compactor in a few minutes.
Handle
6
Vibratory Plate Compactor
Unfold the Handle as shown.
1.
Mount the Handle as shown. Make the Handle
Ends slot into the channels provided by the
Engine Deck. Place
fl
at washers 10, followed by
hex bolts M10x70 at the outer side, and tighten
with lock nuts M10 at the inner side.
2.
Unscrew bolt 5X35 from throttle control.
Secure the Throttle Control onto the Upper
Handle with a
fl
at washer 5 and the bolt 5X35
that just were unscrewed.
3.
Fasten the Throttle Control cable with cable
fasteners.
4.
Folding Wheels Kit (Optional)
Line up the holes in the Link Plates and Engine
Deck. Slide bolts M10x30 through the holes from
one side, then lock nuts M10 from the other side.
Tighten down.
1
M10 70
A
2
M5
2
B
M10 30
Before compacting, fold up the Wheel Kit as shown.
Handle
6
Vibratory Plate Compactor
Unfold the Handle as shown.
1.
Mount the Handle as shown. Make the Handle
Ends slot into the channels provided by the
Engine Deck. Place
fl
at washers 10, followed by
hex bolts M10x70 at the outer side, and tighten
with lock nuts M10 at the inner side.
2.
Unscrew bolt 5X35 from throttle control.
Secure the Throttle Control onto the Upper
Handle with a
fl
at washer 5 and the bolt 5X35
that just were unscrewed.
3.
Fasten the Throttle Control cable with cable
fasteners.
4.
Folding Wheels Kit (Optional)
Line up the holes in the Link Plates and Engine
Deck. Slide bolts M10x30 through the holes from
one side, then lock nuts M10 from the other side.
Tighten down.
1
M10 70
A
2
M5
2
B
M10 30
Before compacting, fold up the Wheel Kit as shown.
Handle
6
Vibratory Plate Compactor
Unfold the Handle as shown.
1.
Mount the Handle as shown. Make the Handle
Ends slot into the channels provided by the
Engine Deck. Place
fl
at washers 10, followed by
hex bolts M10x70 at the outer side, and tighten
with lock nuts M10 at the inner side.
2.
Unscrew bolt 5X35 from throttle control.
Secure the Throttle Control onto the Upper
Handle with a
fl
at washer 5 and the bolt 5X35
that just were unscrewed.
3.
Fasten the Throttle Control cable with cable
fasteners.
4.
Folding Wheels Kit (Optional)
Line up the holes in the Link Plates and Engine
Deck. Slide bolts M10x30 through the holes from
one side, then lock nuts M10 from the other side.
Tighten down.
1
M10 70
A
2
M5
2
B
M10 30
Before compacting, fold up the Wheel Kit as shown.
Handle
6
Vibratory Plate Compactor
Unfold the Handle as shown.
1.
Mount the Handle as shown. Make the Handle
Ends slot into the channels provided by the
Engine Deck. Place
fl
at washers 10, followed by
hex bolts M10x70 at the outer side, and tighten
with lock nuts M10 at the inner side.
2.
Unscrew bolt 5X35 from throttle control.
Secure the Throttle Control onto the Upper
Handle with a
fl
at washer 5 and the bolt 5X35
that just were unscrewed.
3.
Fasten the Throttle Control cable with cable
fasteners.
4.
Folding Wheels Kit (Optional)
Line up the holes in the Link Plates and Engine
Deck. Slide bolts M10x30 through the holes from
one side, then lock nuts M10 from the other side.
Tighten down.
1
M10 70
A
2
M5
2
B
M10 30
Before compacting, fold up the Wheel Kit as shown.
1. Unfold the handle as shown
2. Mount the handle as shown. Make the handle
ends slot into the channels provided by the engine
deck. Place flat washers 10, followed by hex bolts
M10x70 at the outer side, and tighten with lock
nuts M10 at the inner side.
3. Unscrew bolt 5x35 from throttle control. Secure
the throttle control onto the upper handle with a
flat washer 5 and the bolt 5x35 that just were
unscrewed.
4. Fasten the throttle control cable with cable
fasteners.
Line up the holes in the link plates and engine deck.
Slide bolts M10x30 through the holes from one side,
then lock nuts M10 from the other side. Tighten down.
Before compacting, fold up the wheel kit as shown.
Handle
Folding wheels kit (optional)
copyrighted
document
- all
rights
reserved
by
FBC