MD300 - NLFREN - v1.0 - 17012017
5
NL
Motorschakelaar
De motorschakelaar activeert en deactiveert het ontstekingssysteem.
De schakelaar moet op ON zijn om de motor op te starten.
Zet de schakelaar op OFF om de motor stil te zetten.
Koppelingshendel
Duw de hendel om de koppeling in te schakelen. Laat de hendel los om de koppeling uit te schakelen.
Gashendel
Dient voor de controle van het motorsnelheid. Zet de hendel op lage (L) of hoge (H) snelheid, of in een tussenpositie tussen L en
H, om de motorsnelheid te verhogen of verlagen.
Stuurhendel links
Bedien de hendel om naar links te draaien.
Stuurhendel rechts
Bedien de hendel om naar rechts te draaien.
Versnellingshendel
Dient om de vooruit- of achteruitversnelling in te schakelen.
Kantelhendel
Controleert het kantelen van de laadbak. Draai de hendel A in de richting van de pijl om de begrenzer B van de haak C los te
maken. De laadbak wordt vrijgegeven.
Draai na het lossen van de laadbak de hendel A terug, om de begrenzer B opnieuw in de haak C terug te zetten, zodat de
laadbak opnieuw vergrendelt wordt.
9
Powered Wheelbarrow
Tipping handle
It controls tipping of the dump box. Swing tipping
handle A in the direction of the arrow to release
limiter B out of hook C. The dump box will be
released.
After tipping the load, swing handle A back to
reset limiter B into hook C, which will lock the
dump box.
A
B
C
A
B
C
Before you start to use the dumper,
please check the dump box to make
sure it is locked as shown in the
diagram below.
Fill tank to no more than 12.5mm (1/2”)
below the bottom of the filler neck to
provide space for expansion.
Powered Wheelbarrow Operation
Adding fuel
Fill the fuel tank as instructed in the separate
Engine Manual
packed with the machine.
Starting engine
A more detailed description of the engine operation
and all related precautions and procedures can be
found in the
Engine Manual
packed separately
with the powered wheelbarrow.
Follow the procedure below for cold starts:
Turn choke lever on the engine to full choke
position.
Set the throttle lever on the handlebar at half-
way position.
Turn the engine switch on.
Pull the starting rope slowly several times to
allow the gasoline to flow into the engine’s
carburetor. Then hold the start handle firmly
and pull rope out a short distance until you
feel some resistance. Then pull the rope
smoothly and briskly, and allow rope to return
gently. Do not let the rope snap back. If
necessary, pull the rope several times until the
engine starts.
Allow the engine to run for several seconds to
warm up. Then, gradually move chock lever to
“OPEN” position.
Restarting an engine that is already warm from
previous running does not normally require use of
the choke.
1.
2.
3.
4.
5.
Set the throttle lever on the handlebar at half-
way position.
Hold the start handle firmly and pull rope out
a short distance until you feel some resistance.
Then pull the rope smoothly and briskly, and
allow rope to return gently. Do not let the rope
snap back.
2.
1.
9
Powered Wheelbarrow
Tipping handle
It controls tipping of the dump box. Swing tipping
handle A in the direction of the arrow to release
limiter B out of hook C. The dump box will be
released.
After tipping the load, swing handle A back to
reset limiter B into hook C, which will lock the
dump box.
A
B
C
A
B
C
Before you start to use the dumper,
please check the dump box to make
sure it is locked as shown in the
diagram below.
Fill tank to no more than 12.5mm (1/2”)
below the bottom of the filler neck to
provide space for expansion.
Powered Wheelbarrow Operation
Adding fuel
Fill the fuel tank as instructed in the separate
Engine Manual
packed with the machine.
Starting engine
A more detailed description of the engine operation
and all related precautions and procedures can be
found in the
Engine Manual
packed separately
with the powered wheelbarrow.
Follow the procedure below for cold starts:
Turn choke lever on the engine to full choke
position.
Set the throttle lever on the handlebar at half-
way position.
Turn the engine switch on.
Pull the starting rope slowly several times to
allow the gasoline to flow into the engine’s
carburetor. Then hold the start handle firmly
and pull rope out a short distance until you
feel some resistance. Then pull the rope
smoothly and briskly, and allow rope to return
gently. Do not let the rope snap back. If
necessary, pull the rope several times until the
engine starts.
Allow the engine to run for several seconds to
warm up. Then, gradually move chock lever to
“OPEN” position.
Restarting an engine that is already warm from
previous running does not normally require use of
the choke.
1.
2.
3.
4.
5.
Set the throttle lever on the handlebar at half-
way position.
Hold the start handle firmly and pull rope out
a short distance until you feel some resistance.
Then pull the rope smoothly and briskly, and
allow rope to return gently. Do not let the rope
snap back.
2.
1.
9
Powered Wheelbarrow
Tipping handle
It controls tipping of the dump box. Swing tipping
handle A in the direction of the arrow to release
limiter B out of hook C. The dump box will be
released.
After tipping the load, swing handle A back to
reset limiter B into hook C, which will lock the
dump box.
A
B
C
A
B
C
Before you start to use the dumper,
please check the dump box to make
sure it is locked as shown in the
diagram below.
Fill tank to no more than 12.5mm (1/2”)
below the bottom of the filler neck to
provide space for expansion.
Powered Wheelbarrow Operation
Adding fuel
Fill the fuel tank as instructed in the separate
Engine Manual
packed with the machine.
Starting engine
A more detailed description of the engine operation
and all related precautions and procedures can be
found in the
Engine Manual
packed separately
with the powered wheelbarrow.
Follow the procedure below for cold starts:
Turn choke lever on the engine to full choke
position.
Set the throttle lever on the handlebar at half-
way position.
Turn the engine switch on.
Pull the starting rope slowly several times to
allow the gasoline to flow into the engine’s
carburetor. Then hold the start handle firmly
and pull rope out a short distance until you
feel some resistance. Then pull the rope
smoothly and briskly, and allow rope to return
gently. Do not let the rope snap back. If
necessary, pull the rope several times until the
engine starts.
Allow the engine to run for several seconds to
warm up. Then, gradually move chock lever to
“OPEN” position.
Restarting an engine that is already warm from
previous running does not normally require use of
the choke.
1.
2.
3.
4.
5.
Set the throttle lever on the handlebar at half-
way position.
Hold the start handle firmly and pull rope out
a short distance until you feel some resistance.
Then pull the rope smoothly and briskly, and
allow rope to return gently. Do not let the rope
snap back.
2.
1.
Kantelhendel
Kantelhendel
AANDACHT!
Alvorens de kuipwagen op te
starten, controleer dat de laadbak
correct vergrendeld is, zoals op de
afbeelding.
Vergrendelde laakbak
copyrighted
document
- all
rights
reserved
by
FBC
