23
MD300 - NLFREN - v1.0 - 17012017
EN
Engine switch
The engine switch enables and disables the ignition system.
The engine switch must be in the ON position for the engine to run.
Turning the engine switch to the OFF position stops the engine.
Clutch control lever
Squeeze the control lever, clutch engaged. Release the lever, clutch disengaged.
Throttle control
It controls engine speed. Put the throttle control on low speed (L) or high speed (H) or an intermediary position between L and H
to increase or decrease the speed of engine.
Left steering lever
Operate the lever to turn left.
Right steering lever
Operate the lever to turn right.
Gear selection lever
It controls forward or reverse movements of the machine.
Tipping handle
It controls tipping of the dump box. Swing tipping handle A in the direction of the arrow to release limiter B out of hook C. The
dump box will be released.
After tipping the load, swing handle A back to reset limiter B into hook C, which will lock the dump box.
9
Powered Wheelbarrow
Tipping handle
It controls tipping of the dump box. Swing tipping
handle A in the direction of the arrow to release
limiter B out of hook C. The dump box will be
released.
After tipping the load, swing handle A back to
reset limiter B into hook C, which will lock the
dump box.
A
B
C
A
B
C
Before you start to use the dumper,
please check the dump box to make
sure it is locked as shown in the
diagram below.
Fill tank to no more than 12.5mm (1/2”)
below the bottom of the filler neck to
provide space for expansion.
Powered Wheelbarrow Operation
Adding fuel
Fill the fuel tank as instructed in the separate
Engine Manual
packed with the machine.
Starting engine
A more detailed description of the engine operation
and all related precautions and procedures can be
found in the
Engine Manual
packed separately
with the powered wheelbarrow.
Follow the procedure below for cold starts:
Turn choke lever on the engine to full choke
position.
Set the throttle lever on the handlebar at half-
way position.
Turn the engine switch on.
Pull the starting rope slowly several times to
allow the gasoline to flow into the engine’s
carburetor. Then hold the start handle firmly
and pull rope out a short distance until you
feel some resistance. Then pull the rope
smoothly and briskly, and allow rope to return
gently. Do not let the rope snap back. If
necessary, pull the rope several times until the
engine starts.
Allow the engine to run for several seconds to
warm up. Then, gradually move chock lever to
“OPEN” position.
Restarting an engine that is already warm from
previous running does not normally require use of
the choke.
1.
2.
3.
4.
5.
Set the throttle lever on the handlebar at half-
way position.
Hold the start handle firmly and pull rope out
a short distance until you feel some resistance.
Then pull the rope smoothly and briskly, and
allow rope to return gently. Do not let the rope
snap back.
2.
1.
9
Powered Wheelbarrow
Tipping handle
It controls tipping of the dump box. Swing tipping
handle A in the direction of the arrow to release
limiter B out of hook C. The dump box will be
released.
After tipping the load, swing handle A back to
reset limiter B into hook C, which will lock the
dump box.
A
B
C
A
B
C
Before you start to use the dumper,
please check the dump box to make
sure it is locked as shown in the
diagram below.
Fill tank to no more than 12.5mm (1/2”)
below the bottom of the filler neck to
provide space for expansion.
Powered Wheelbarrow Operation
Adding fuel
Fill the fuel tank as instructed in the separate
Engine Manual
packed with the machine.
Starting engine
A more detailed description of the engine operation
and all related precautions and procedures can be
found in the
Engine Manual
packed separately
with the powered wheelbarrow.
Follow the procedure below for cold starts:
Turn choke lever on the engine to full choke
position.
Set the throttle lever on the handlebar at half-
way position.
Turn the engine switch on.
Pull the starting rope slowly several times to
allow the gasoline to flow into the engine’s
carburetor. Then hold the start handle firmly
and pull rope out a short distance until you
feel some resistance. Then pull the rope
smoothly and briskly, and allow rope to return
gently. Do not let the rope snap back. If
necessary, pull the rope several times until the
engine starts.
Allow the engine to run for several seconds to
warm up. Then, gradually move chock lever to
“OPEN” position.
Restarting an engine that is already warm from
previous running does not normally require use of
the choke.
1.
2.
3.
4.
5.
Set the throttle lever on the handlebar at half-
way position.
Hold the start handle firmly and pull rope out
a short distance until you feel some resistance.
Then pull the rope smoothly and briskly, and
allow rope to return gently. Do not let the rope
snap back.
2.
1.
9
Powered Wheelbarrow
Tipping handle
It controls tipping of the dump box. Swing tipping
handle A in the direction of the arrow to release
limiter B out of hook C. The dump box will be
released.
After tipping the load, swing handle A back to
reset limiter B into hook C, which will lock the
dump box.
A
B
C
A
B
C
Before you start to use the dumper,
please check the dump box to make
sure it is locked as shown in the
diagram below.
Fill tank to no more than 12.5mm (1/2”)
below the bottom of the filler neck to
provide space for expansion.
Powered Wheelbarrow Operation
Adding fuel
Fill the fuel tank as instructed in the separate
Engine Manual
packed with the machine.
Starting engine
A more detailed description of the engine operation
and all related precautions and procedures can be
found in the
Engine Manual
packed separately
with the powered wheelbarrow.
Follow the procedure below for cold starts:
Turn choke lever on the engine to full choke
position.
Set the throttle lever on the handlebar at half-
way position.
Turn the engine switch on.
Pull the starting rope slowly several times to
allow the gasoline to flow into the engine’s
carburetor. Then hold the start handle firmly
and pull rope out a short distance until you
feel some resistance. Then pull the rope
smoothly and briskly, and allow rope to return
gently. Do not let the rope snap back. If
necessary, pull the rope several times until the
engine starts.
Allow the engine to run for several seconds to
warm up. Then, gradually move chock lever to
“OPEN” position.
Restarting an engine that is already warm from
previous running does not normally require use of
the choke.
1.
2.
3.
4.
5.
Set the throttle lever on the handlebar at half-
way position.
Hold the start handle firmly and pull rope out
a short distance until you feel some resistance.
Then pull the rope smoothly and briskly, and
allow rope to return gently. Do not let the rope
snap back.
2.
1.
Tipping handle
Tipping handle
WARNING!
Before you start to use the dumper,
please check the dump box to make
sure it is locked as shown in the
diagram.
Dump box locked
copyrighted
document
- all
rights
reserved
by
FBC
