manualshive.com logo in svg

Mustang Survival MD3188, Руководство производителя

Поделиться
Скачать
Mustang Survival MD3188 Скачать руководство пользователя страница 29

26

HOW AND WHY TO TEST YOUR PFD

Inflate your PFD and try it out in the water to:

Make sure it floats you:

•  Comfortably (when worn properly)
•  Adequately for expected wave conditions (body shapes / densities 

affect performance)

Make sure it works:

•  A flow of bubbles should not appear (see “Care and Maintenance 

Instructions for Leak Test,” page 19). It should inflate quickly and 
easily.

Learn how it works by:

•  Activating the CO

2

 inflation system

•  Re-arming the CO

2

 inflation system

•  Using the oral inflator tube 

HOW TO TEST YOUR PFD USING THE 

AUTOMATIC INFLATOR

The US Coast Guard recommends that you purchase at least two 
spare re-arming kits (MA7214).

A

1.  To test your inflatable PFD, you will need your fully armed PFD,  

  and the re-arming kit (MA7214) approved for your PFD.

A

2. Put on the PFD.

A

3. Get into shallow water, just deep enough that you can stand with  

  your head above the surface. Once the inflator is underwater, four  
  inches or so, the PFD should fully inflate automatically within five  
 seconds.

A

4. See if the PFD will float you on your back or just slightly back of  

  vertical. In a relaxed floating position, verify that your mouth is  
  well above the water’s surface. Note the effect of where you hold  
  your legs on how you float.

A

5. Get out of the water and remove the PFD.

A

6. Deflate the PFD by depressing the oral inflator valve (see   

  “Deflating Your PFD,” page 9). Remove the used inflator.

A

7. Let the PFD dry thoroughly. Re-arm (page 10) and repack  

  (page 14) the PFD.

Содержание MD3188





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды