Mustang Survival MD3188 страница 23 Скачать руководство пользователя | Manualshive

Страница: 23 / 36

background image

20

ANNUALLY

Perform the following annually, or whenever the integrity of the PFD
is in doubt:

• Perform a thorough inspection. Refer to the “Every Three Months”

section.

• Perform the Leak Test in the “Every Three Months” section.

• Clean the PFD. Check for dirt and corrosion and replace all

corroded parts. See “Cleaning and Stowage of Your PFD,” page 21.

• Record as an “Annual” inspection in permanent ink on the Service

Record label on the PFD. Repack the PFD as outlined in the
repacking section, page 14.

EVERY FIVE YEARS

• Perform a thorough inspection. Refer to the “Every Three Months”

section.

• Test the auto-inflation mechanism (see “Inflating Your PFD,” page 7)

by submerging the device in at least four inches of water. The device
should inflate within five seconds.

• Perform the Leak Test in the “Every Three Months” section.

• Clean the PFD. Check for dirt and corrosion and replace all

corroded parts. See “Cleaning and Stowage of Your PFD,” page 21.

• Record as an “Annual” inspection in permanent ink on the Service

Record label on the PFD. Write an asterisk (*) next to the date to
mark each five year inspection.

Re-arm and repack the PFD as outlined in the re-arming (page 10)
and repacking (page 14) sections.

WARNING: IF YOU ARE NOT CONFIDENT IN THE SELF-INSPECTION AND SERVICING
OF YOUR PFD IN ACCORDANCE WITH THESE INSTRUCTIONS, TAKE YOUR PFD TO A
MUSTANG DEALER FOR PROFESSIONAL SERVICING OR CONTACT MUSTANG SURVIVAL.

«
...
21
22
23
24
25
...
»

Содержание MD3188





































Отзывы:

Нет отзывов

Похожие инструкции для MD3188

Бренд: Lalizas Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды