manualshive.com logo in svg

Mustang Survival MD3188, Руководство производителя

Поделиться
Скачать
Mustang Survival MD3188 Скачать руководство пользователя страница 13

10

2.  Gently squeeze the PFD 

until all air or gas has been 
expelled. To avoid damage, 
do not wring or twist the 
PFD. Put the inflation tube 
cap back in its stowed 
position on the oral inflation 
tube (Fig. 7).

ENSURE ALL AIR HAS BEEN REMOVED 
FROM THE PFD.

3.  Examine the single point 

status indicator (Fig. 2). 
If the indicator is red, the 
mechanism has been fired 
and the inflator requires 
service (see “Re-arming 
Your PFD,” below).

THE SINGLE POINT STATUS INDICATOR MUST BE GREEN BEFORE PROCEEDING.

4.  Your device is ready to be repacked (see “Repacking Your PFD,” 

page 14).

RE-ARMING YOUR PFD

A VALID RE-ARM KIT (MA7214) IS REQUIRED FOR THIS PROCEDURE.

Warning

•  This gas cylinder is under pressure, therefore misuse can be 

dangerous.

•  Do not incinerate, expose to sunlight, or store above 120°F (50°C).
•  Do not throw into open fire or dump at sea.
•  Keep away from children.
•  Dispose of gas cylinders only when empty.
•  Discharge and dispose of corroded or rusty cylinders.

Stowed 
position

Deflate 
position

FIGURE 7

ORAL INFLATION CAP

Содержание MD3188





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды