Murray 6291570X54, Инструкция

Страница: 15 / 181

en
15
1740877
2. Disconnect the spark plug wire.
3. (Figure 28) Remove the bolts (1) on each
side of the bottom panel (2).
4. Loosen the bolts (3) on each side of the
bottom panel (2).
5. Remove the bottom panel (2).
6. (Figure 29) Remove the rear support brace
(18).
7. (Figure 30) Use a 3/16” allen wrench and
remove the fastener that secures the right
axle clamp (30) to the axle (34).
8. Remove the right wheel (35), axle (34), axle
clamp (30), and washer (31).
9. (Figure 28) Remove the left wheel (10) from
the axle (11).
10. (Figure 31) Remove the fasterners that
secure the axle suport (32) to the motorbox.
Remove the axle suport (32) and bushing
(33).
11. Loosen (do not remove) the bolts that secure
the axle bearings (19) to the motor box.
12. Remove the clutch/drive sprocket
assembly (20) from the axle (11).
13. (Figure 32) Remove the four bolts (16) that
hold the bearings (7) on each side of the
hex shaft (8).
14. (Figure 33) Remove the hex shaft (8) and
bearings (7).
NOTE: Take special note of the position of
the washers (13).
15. (Figure 26) Remove the three fasteners (4)
that hold the friction wheel (5) to the hub
(6).
16. (Figure 26) Remove the friction wheel (5)
from the hub (6). Slip the friction wheel (5)
off the hex shaft (8).
17. Assemble the new friction wheel (5) onto
hub (6) with the fasteners removed earlier.
18. (Figure 33) Install the hex shaft (8) and
bearings (7) with the four bolts removed
earlier.
Make sure the washers (17) are properly
installed in the original position. Also,
make sure the two washers (13) are
properly aligned with the actuator arms
(14).
19. Make sure the hex shaft (8) turns freely.
20. To install the remaining parts, reverse the
above steps.
21. Check the adjustment of the friction wheel.
See “How To Adjust The Friction Wheel” in
this section.
22. Make sure the friction wheel and the disc
drive plate are free from grease or oil.
23. (Figure 28) Install the bottom panel (2).
24. Install the bolts (1) on each side of the
bottom panel (2).
25. Tighten the bolts (1) and bolts (3) on each
side of the bottom panel (2).
26. Connect the spark plug wire.
How To Replace the Auger Shear Bolt
The augers are secured to the auger shaft with
special shear bolts. These shear bolts are
designed to break and protect the machine if an
object becomes lodged in the auger housing. Do
not use a harder bolt as the protection provided
by the shear bolt will be lost.
WARNING: For safety and to
protect the machine, use only
original equipment shear bolts.
To replace a broken shear bolt, proceed as
follows. Extra shear bolts were provided in the
assembly parts bag.
1. (Figure 1) Stop the engine. Disengage all
controls.
2. Disconnect the spark plug wire. Make sure
all moving parts have stopped.
3. (Figure 14) Lubricate the auger shaft Zerk
fitting (1), if equipped, with a grease gun.
4. (Figure 25) Align the hole in the auger with
the hole in the auger shaft. Install the new
shear bolt (2), spacer (3), and locknut (4).
NOTE: If the model has a 33” (84 cm)
Auger Housing, the spacer (3) is not
required.
5. Connect the spark plug wire.
How To Prepare The Snow Thrower For
Storage
WARNING: Do not remove gasoline
while inside a building, near a fire,
or while you smoke. Gasoline
fumes can cause an explosion or a fire.
If the snow thrower is to be stored for an
extended period, refer to the engine
manufacturer’s operating manual (included with
some models) for important maintenance or
storage details.
1. Drain the fuel tank.
2. Let the engine run until it is out of gasoline.
3. Never store the snow thrower with fuel in the
tank inside a building where ignition sources
are present such as hot water and space
heaters, clothes dryers, and the like. Allow
the engine (motor) to cool before storing in
any enclosure.
4. Drain the oil from the warm engine. Fill the
engine crankcase with new oil.
5. Remove the spark plug from the cylinder.
Pour one ounce (29.6 ml) of oil into the
cylinder. Slowly pull the recoil−start grip so
that the oil will protect the cylinder. Install a
new spark plug in the cylinder.
6. Thoroughly clean the snow thrower.
7. Lubricate all lubrication points. See the
Maintenance section.
8. Be sure that all nuts, bolts and screws are
securely fastened. Inspect all visible moving
parts for damage, breakage and wear.
Replace if necessary.
9. Cover the bare metal parts of the blower
housing, auger, and the impeller with spray
rust preventative lubricant.
10. Put the unit in a building that has good
ventilation.
11. If the machine must be stored outdoors,
block up the snow thrower to be sure the
entire machine is off the ground.
12. Cover the snow thrower with a suitable
protective cover that does not retain
moisture. Do not use plastic.
How To Order Replacement Parts
The replacement parts are shown either on the
back pages of this Instruction Book or in a
separate Parts List Book.
Use only manufacturer’s authorized or approved
replacement parts. Do not use attachments or
accessories not specifically recommended for
this unit. In order to obtain proper replacement
parts you must supply the model number (see
nameplate).
To obtain replacement parts, contact your local
Dealer.
Replacement parts for the engine, transaxle, or
transmission, are available from the
manufacturer’s authorized service centre found
in the yellow pages of the telephone directory.
Also, see the individual engine or transmission
warranties to order replacement parts.
When ordering the following information is
required:
(1) The Model Number
(2) Serial Number
(3) Part Number
(4) Quantity