Murray 405000x8E страница 25 Скачать руководство пользователя

Страница: 25 / 52

MAINTENANCE

F-050700L

HOW TO ADJUST THE SHIFT LEVER

If the NEUTRAL position on the shift lever does not match neutral

on the gearbox, adjust the shift lever as follows.

1. Stop the engine.

2. Disconnect the

adjuster nut

from the

shifter bracket

(Figure 18).

3. Make sure the shift lever is in the NEUTRAL position.

4. Push the unit forward. Make sure the gearbox is in neutral.

5. To align the

adjuster nut

with the hole in the

shifter bracket

turn the

adjuster nut

6. Connect the

adjuster nut

to the

shifter bracket

7. Make sure the NEUTRAL position on the shift lever matches

neutral on the gearbox.

Adjuster Nut

Hair

Shift

Link

Shifter

Bracket

Motion Drive Belt

Figure 18

Shift Lever

MAINTENANCE FREE BATTERY

HOW TO REMOVE THE BATTERY

To charge or clean the

battery

, remove the

battery

from the unit as

follows.

WARNING: To prevent sparks, disconnect the black

battery cable from the negative (-) terminal before you

disconnect the red cable.

WARNING: The battery contains sulfuric acid which is

harmful to the skin, eyes and clothing. If the acid gets

on the body or clothing, wash with water.

1. Disconnect the

black cable

from the negative (-) terminal

(Figure 19).

2. Disconnect the

red cable

from the

positive (+) terminal.

3. Lift the

battery tray

and the

battery

out of the unit.

HOW TO CLEAN THE BATTERY

1. Remove the

battery

2. Wash the

battery

with a solution of one gallon of water and four

tablespoons of baking soda (sodium bicarbonate). Make sure

the solution does not get into the battery cells.

3. Clean the

terminals

and the ends of the

cables

with a wire

brush.

4. Install the

battery

5. To prevent corrosion, apply grease to the

battery terminals

HOW TO CHARGE THE BATTERY

WARNING: When you charge the battery, do not

smoke. Keep the battery away from any sparks. The

fumes from the battery acid can cause an explosion.

1. Before you charge the

battery

, remove the

battery

2. To charge the

battery

, use a 12 volt battery charger. Charge at

a rate of 6 amperes for 1 hour.

3. Install the

battery.

WARNING: To prevent sparks, fasten the red cable to

the positive (+) terminal before you connect the black

cable.

4. Fasten the

red cable

to the

positive (+) terminal

with the fas-

teners as shown.

5. Fasten the

black cable

to the negative (-) terminal with the fas-

teners as shown.

Positive (+)

Terminal

Black Cable

Red Cable

Battery Tray

Battery

Figure 19

Carriage Bolt

Wing Nut

Carriage Bolt

Содержание 405000x8E





















































Результаты поиска

Содержание 405000x8E

Отзывы:

Похожие инструкции для 405000x8E

Бренды по названию

Популярные бренды

Murray 405000x8E, Инструкция

Результаты поиска

Содержание 405000x8E

Отзывы:

Похожие инструкции для 405000x8E

Бренды по названию

Популярные бренды