Murray 405000x8E Скачать руководство пользователя

Страница: 16 / 52

OPERATION

F-050700L

HOW TO USE

THE BLADE ROTATION CONTROL

The

blade rotation control

is next to the steering wheel (Figure 6).

Use the

blade rotation control

to engage the blade(s) or to operate

a snow thrower attachment.
1. Before you start the engine, make sure the

blade rotation con-

trol

is in the

DISENGAGE position

2. Move the

blade rotation control

to the

ENGAGE position

rotate the blade(s).

Note: If the engine stops when you engage the blade(s),

the transmission is in reverse.

3. Move the

blade rotation control

to the

DISENGAGE position

to stop the blade(s). Before you leave the operator’s position,

make sure the blade(s) has stopped rotating.

4. Before you ride the unit across a sidewalk or a road, move the

blade rotation control

to the

DISENGAGE position.

5. Before operating in reverse, move the blade rotation control to

the

DISENGAGED position.

If the blade rotation control is not

in the

DISENGAGED position,

the engine will stop when the

speed control pedal/shift lever is moved to REVERSE position.

WARNING: Always keep your hands and feet away

from the blade, deflector opening, and the mower

housing when the engine runs.

Blade Rotation Control

Engage Position

Disengage

Position

Figure 6

HOW TO USE THE SHIFT LEVER

To change the forward speed or the direction of the unit, follow the

steps below.

CAUTION: Before you move the shift lever, completely push

the clutch/brake pedal forward to stop the unit. If the unit is not

stopped, the gearbox can be damaged.

1. Completely push the clutch/brake pedal forward to stop the

unit. Keep your foot on the pedal.

2. Move the throttle control lever to the SLOW position.
3. To go forward, move the shift lever to a forward speed setting.
4. To go backward, move the shift lever to reverse. Always disen-

gage blades and look down and behind before and while back-

ing.

5. Slowly release the clutch/brake pedal. Do not keep your foot on

the pedal.

6. Move the throttle control to the FAST position.

FUNCTION

SHIFT LEVER

5−6 Speeds

THROTTLE

Trimming

Snow Thrower

Bagging Grass

1 or 2

FAST

Mulching Grass

1 or 2

FAST

CHOKE

Normal Mowing

2 or 3

FAST

Easy Mowing

Snow Blade

3 or 4

SLOW

Transport

5-6

THROTTLE

Attachments

* See the Instruction Book for the Attachment.

Содержание 405000x8E





















































Результаты поиска

Содержание 405000x8E

Отзывы:

Похожие инструкции для 405000x8E

Бренды по названию

Популярные бренды

Murray 405000x8E, Инструкция

Результаты поиска

Содержание 405000x8E

Отзывы:

Похожие инструкции для 405000x8E

Бренды по названию

Популярные бренды