Murray 405000x8E страница 9 Скачать руководство пользователя

Страница: 9 / 52

INTERNATIONAL PICTORIALS

F-050700L

INTERNATIONAL PICTORIALS

IMPORTANT: Some of the following pic-

torials are located on your unit or on

literature supplied with the product. Be-

fore you operate the unit, learn and un-

derstand the purpose for each pictorial.

Safety Warning Pictorials

Warning

Shield Eyes. Explosive Gases Can
Cause Blindness Or Injury.

No Sparks, Flames or Smoking.

Sulphuric Acid Can Cause Blindness
Or Severe Burns

Flush Eyes Immediately With Water.
Get Medical Help Fast.

IMPORTANT: Read Owner’s Manual
Before Operating This Machine.

WARNING: Thrown Objects. Keep
Bystanders Away. Read User
Instructions Before Operating This
Machine.

WARNING: Do Not Use This Machine
On Slopes Greater Than 15 Degrees.

DANGER: Keep People, Especially
Children, Away From Unit.

DANGER: No Step.

DANGER: Keep Feet And Hands
Away From Rotating Blade.

DANGER: Keep Hands Away From
Rotating Blade.

DANGER: Disconnect Spark Plug
Wire Before Servicing Unit.

WARNING: Hot Surface.

WARNING: Use Caution When
Connecting Or Disconnecting
Accessories.

WARNING: Crushed Fingers.

MAX 90N

MAX 150N

Control And Operating Pictorials

Engine Start

Lights

Engine Stop

Select Reverse

Engine Run

Engine Start

Brake

Parking Brake

Clutch

Slow

Fast

Choke

Oil

Blade Rotation Control

Raise

Fuel

Содержание 405000x8E





















































Результаты поиска

Содержание 405000x8E

Отзывы:

Похожие инструкции для 405000x8E

Бренды по названию

Популярные бренды

Murray 405000x8E, Инструкция

Результаты поиска

Содержание 405000x8E

Отзывы:

Похожие инструкции для 405000x8E

Бренды по названию

Популярные бренды