Murray 405000x8E Скачать руководство пользователя

Страница: 12 / 52

ASSEMBLY

F-050700L

MAINTENANCE FREE BATTERY

IMPORTANT: Before you attach the battery cables to the

battery, check the battery date. The battery date tells if the

battery must be charged.

1. Check the top and the side of the battery for the location of the

battery date

(Figure 3).

2. If the

battery

is put into service

before

the

battery date

, the

battery

cables can be attached without charging the

battery

See “How To Install The Battery Cables”.

3. If the

battery

is put into service

after

the

battery date

, the

battery

must be charged. See “How To Charge The

Maintenance Free Battery”.

HOW TO CHARGE

THE MAINTENANCE FREE BATTERY

WARNING: When you charge the battery, do not

smoke. Keep the battery away from any sparks. The

fumes from the battery acid can cause an explosion.

1. Remove the

battery

and

battery tray.

2. Remove the protective caps from the

battery terminals

3. Use a 12 volt battery charger to charge the

battery

. Charge at

a rate of 6 amperes for one hour. If you do not have a battery

charger, have an authorized service center charge the battery.

4. Install the

battery

and

battery tray

. Make sure the

positive (+)

terminal

is on the left side.

HOW TO INSTALL THE BATTERY CABLES

WARNING: To prevent sparks, fasten the red cable to

the positive (+) terminal before you connect the black

cable.

Use the fasteners shown below to install the

battery cables

. The

fasteners are shown at full size.

(B)

14x79

(A)

2x82

1. Remove the protective caps from the

battery terminals

2. Fasten the

red cable

to the

positive (+) terminal

with the

fasteners as shown (Figure 3).

3. Fasten the

black cable

to the negative (-) terminal with the

fasteners as shown.

Positive (+)

Terminal

Black Cable

Red Cable

Battery Tray

Battery

Figure 3

Содержание 405000x8E





















































Результаты поиска

Содержание 405000x8E

Отзывы:

Похожие инструкции для 405000x8E

Бренды по названию

Популярные бренды

Murray 405000x8E, Инструкция

Результаты поиска

Содержание 405000x8E

Отзывы:

Похожие инструкции для 405000x8E

Бренды по названию

Популярные бренды