background image

VALVE CUT-OUT

A.

 Main Stem

B.

 Pressure Disc/seal (in run/open)

C.

 Pressure Disc/seal (in trip/closed)

D.

 Vent Seal Gland

E.

 Reset Knob (latches valve open)

F.

 Manual Trip Knob (not available for M5081FS) 

G. 

Indicator Button (out with valve open) 

H. 

Pipe Plug

A

B

D

E

F

Understanding the Basic Operation

of the Fuel Shut-off Valve

The valve below is shown in the run (open) position.
Pressure is equalized, seat (

B

) is open, allowing 

the fuel to flow. When valve is in the tripped position
(closed), seat closes (

C

).

The vent (

D

) opens to relieve trapped downstream fuel

to vent to a non-hazardous area. 

C

NOTE:

 If the vent-after-tripping feature is not used,

remove O-ring (

D

), to avoid condensation accumulation

that can hamper trip action. 

Be sure

 to replace Pipe Plug (

H

) and to clean vent

periodically.

Vent to relieve trapped fuel
outside the hazardous area. 

Terminal Block is 
within this case.

G

Pipe Plug (remove to
install vent tube). 

TYPICAL MODEL (M5081) SHOWN

H

FLOW CHARACTERISTICS

250

[7.08]

500

[14.16]

1000

[28.32]

1250

[35.40]

1500

[42.48]

1750

[4956]

2000

[56.64]

2250

[63.72]

2500

[70.80]

3000

[84.96]

2750

[77.88]

750

[21.24]

0

1.0

[25.4]

2.0

[50.8]

3.0

[76.2]

4.0

[101.6]

5.0

[127.0]

6.0

[152.4]

7.0

[177.8]

8.0

[203.2]

9.0

[228.6]

10.0

[254.0]

4 oz. (0.11 kg.) 

10 oz. (0.28 kg.)

5 psig (34 kPa) [0.34 bar]

10 psig (69 kPa) [0.69 bar]

20 psig (138 kPa) [1.38 bar]

30 psig (207 kPa) [2.07 bar]

4 oz. (0.11 kg.) 

10 oz. (0.28 kg.)

5 psig (34 kPa) [0.34 bar]

10 psig (69 kPa) [0.69 bar]

20 psig (138 kPa) [1.38 bar]

30 psig (207 kPa) [2.07 bar]

4 oz. (.11 kg.)

4 oz. (.11 kg.)

10 oz. (.28 kg.)

10 psig (69 kPa) [.69 bar]

20 psig (138 kPa) [1.38 bar]

30 psig (207 kPa) [2.07 bar]

500

[14.16]

1000

[28.32]

2000

[56.64]

2500

[70.80]

3000

[84.96]

3500

[99.12]

4000

[113.28]

4500

[127.44]

5000

[141.60]

1500

[42.48]

0

1.0

[25.4]

2.0

[50.8]

3.0

[76.2]

4 oz. (.11 kg.)

10 oz. (.28 kg.)

10 psig (69 kPa) [.69 bar]

20 psig (138 kPa) [1.38 bar]

30 psig (207 kPa) [2.07 bar]

M2582 Series

M5081 and
M5180 Series

Inches water column (

p) drop across valve.

Millimeters water column in brackets [ ].

Standard cubic feet per hour. Cubic meters per hour in brackets [ ].

Inches water column (

p) drop across valve.

Millimeters water column in brackets [ ].

Standard cubic feet per hour. Cubic meters per hour in brackets [ ].

Installation M-7980N page 2 of 12

1-800-548-1191 - http://www.partdeal.com - [email protected]

Содержание M5081FS













Отзывы: