Munsch MAK-40 Скачать руководство пользователя страница 14

 
 

Hand Extruder MEK-40,65 / MAK-40,65 

 

Page 14/20 

Issue 08.2008/Rev. 01 

MUNSCH Kunststoff-Schweißtechnik GmbH 

 

6  Maintenance/Inspection 

 

 Pull mains connector before carrying out any 

maintenance and repair work on the hand extruder.        

 

Maintenance and repair work on electrical tools may 
only be carried out by qualified electricians. 

 The hand extruder together with the hot air 

hood must have cooled down to safe-to-touch tem-
perature.  

 

Observe the instructions under section “Safety“.  
 
Maintenance and repair work may only be carried  
out by qualified personnel or by our service staff.  
 
To ensure the proper function of the hand extruder 
over its entire service life for its intended service, we 
recommend:  

to have all maintenance, inspection and mounting 
work carried out by authorized and qualified per-
sonnel who are familiar with the operating instruc-
tions, 

to always shut off the unit before carrying out any 
work on it,  

to remount and reactivate all safety and protec-
tive devices immediately after completion of the 
maintenance/repair work. 

 
During maintenance and repair work, make sure that 
the hand extruder and its individual components are 
firmly positioned. 

 

In addition to the operating instructions and the na-
tional and local accident prevention regulations ap-
plicable at the place of use, the acknowledged tech-
nical rules for safe and proper working practices 
must be observed.  

 

Any working practices posing a safety risk are pro-
hibited. 

 Activities other than those described in this 

section may only be performed at the Manufacturer’s 
workshops! 
 
6.1  Maintenance/inspection of MEK/MAK hand 

extruder 

  CAUTION After approx. 500 operating hours, the 

hand extruder including drive unit must be  
thoroughly cleaned and inspected. This work may  
only be carried out at the manufacturer’s work-
shops.  

  CAUTION Cables, switches, plug-in connections 

must be inspected by qualified staff every three 
months (requirement according to VBG4); the in-
spection results must be documented. 

 

 
6.2  Dismantling 
Prior to dismantling the hand extruder, pull the mains 
connector.  

 

The hand extruder must be at ambient temperature. 

 

Damaged power cables and/or connecting cables 
(between the Powerbox and the hand extruder) must 
be completely replaced. “Mended” cables pose a 
hazard to life and limb. Cable replacement is to be 
carried out by qualified electricians only.  

 

The safety precautions described under sections  
“Safety“ and “Malfunctions, Causes and Remedies“ 
must be strictly adhered to.  

 

 
 

6.2.1  Overview of spare parts/attachments 
 
When ordering spare parts, always indicate the 
serial number of the extruder.  
 
Make sure to use original spare parts only.  
   
For spare parts supply, contact MUNSCH Kunststoff-
Schweißtechnik GmbH.  
 
 
---------------------------------------------------------------------- 
 
                Extruder screw bearing: 
 
             K03701 = Axial bearing (replace) 
             K03702 = Ball bearing (replace) 
             K03703 = Circlip (replace, if required) 
             K03704 = Seal ring (replace) 
             K04080 = Spacer ring (replace, if required) 
 
----------------------------------------------------------------------

 

 
       

 

 

Содержание MAK-40





















Отзывы: