MultiVOIP Gatekeeper User Guide
77
Appendix C - SBC Configuration Details
Esc: Quit
F1: Help
F5: Old Values
F6: Load BIOS Defaults
F7: Load Setup Defaults
Pu/Pd/+/-: Modify
(Shift) F2: Color
:SELECT ITEM
ROM / PCI / ISA BIOS (2A59FP6C)
PNP/PCI CONFIGURATION
AWARD SOFTWARE, INC.
DMA-1 assigned to
:PCI/ISA PnP
DMA-3 assigned to
:PCI/ISA PnP
DMA-5 assigned to
:PCI/ISA PnP
DMA-6 assigned to
:PCI/ISA PnP
DMA-7 assigned to
:PCI/ISA PnP
Resources Controlled by
:Manual
Reset Configuration Data
:Disabled
IRQ3 assigned to
:Legacy ISA
IRQ4 assigned to
:Legacy ISA
IRQ5 assigned to
:PCI/ISA PnP
IRQ6 assigned to
:Legacy ISA
IRQ7assigned to
:PCI/ISA PnP
IRQ8 assigned to
:PCI/ISA PnP
IRQ9 assigned to
:PCI/ISA PnP
IRQ10 assigned to
:PCI/ISA PnP
IRQ11 assigned to
:PCI/ISA PnP
IRQ12 assigned to
:PCI/ISA PnP
IRQ13 assigned to
:PCI/ISA PnP
IRQ14 assigned to
:PCI/ISA PnP
IRQ15 assigned to
:PCI/ISA PnP
PCI IRQ Active by
:Level
PCI IDE IRQ Map to
:PCI-Auto
Primary IDE INT#
:A
Secondary IDE INT#
:B
Onboard PCI SCSI Chip
:Enabled
Used MEM base addr
:N/A
Figure C-9. PNP/PCI Configuration
You can manually configure the Plug-and-Play/PCI Devices IRQ. The default setting is
Auto
.
PCI IRQ Activated by
This sets the method by which the PCI bus recognizes that an IRQ service is being requested by a
device. Under all circumstances, you should retain the default configuration unless advised otherwise by
your systems manufacturer.
Choices are Level (default) and Edge.
PCI IDE IRQ Map to
This enables you to configure your system to the type of IDE disk controller in use, ISA or PCI (default
value is PCI Auto). PCI Auto enables the system to determine automatically how your IDE disk system is
configured. Remember that this setting refers to the hard disk drive itself, rather than individual
partitions. Since each IDE controller supports two separate hard drives, you can select the interrupt
number (the INT#; the possible values are A, B, C, or D) for each. Note that the primary drive always
has a lower interrupt than the secondary drive.
Onboard PCI SCSI Chip
Default is
Disabled
. The IPC-551 SBC does not support SCSI.
Load BIOS Defaults
Auto Configuration with BIOS Defaults
Choosing LOAD BIOS DEFAULTS from the CMOS Setup Utility menu will restore default BIOS values to
the PC. Invoking LOAD BIOS DEFAULTS will bring up this dialog box:
Load BIOS Default ( Y ? N ) ? Y
To use the BIOS defaults, change the prompt to Y and press
Enter
; the default BIOS values will be
loaded into CMOS automatically the next time you power up the SBC.
Load BIOS Defaults
are the same
as
Load Setup Defaults
.
Load Setup Defaults
Auto Configuration with Setup Defaults
Choosing LOAD SETUP DEFAULTS from the CMOS Setup Utility menu will restore default SETUP values
to the PC. Invoking LOAD SETUP DEFAULTS brings up this dialog box:
Load SETUP Default ( Y ? N ) ? Y
Содержание MultiVOIP MVPGK1 Gatekeepers
