Multitech CommPlete MT5634HD8 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 99

Multitech CommPlete MT5634HD8 Скачать руководство пользователя страница 8

MT5634HD8 User Guide

2

CommPlete Communications Server

Introduction

The Multi-Tech MT5634HD8 is a high speed, high density modem card for the
CommPlete Communications Server. Each MT5634HD8 card contains eight inte-
grated 56Kflex modems. Each modem on the MT5634HD8 card can be configured
independently of the others via RASexpress Software or the CommPlete
Communications Server’s MR9600 controller, which can support and control up to 12
modem cards per rack. Users dial into the MT5634HD8’s modems through a T1
daughter card on the RASCard that controls the segment. There are no external
connectors.

Three MT5634HD8 cards must be installed per T1 segment. With eight modems per
card, the CommPlete Communications Server can support up to 24 simultaneous data
lines per segment, or 96 per CommPlete Communications Server

The MT5634HD8 operates as an enhanced ITU-T V.34 dial-up modem with a maxi-
mum K56flex speeds, and is a fully digital K56flex server. As such, it includes the
advanced features of Multi-Tech standalone modems such as the popular
MultiModemZDXb.

The MT5634HD8 is registered by the {xe "FCC regulations"}FCC for direct
connection to the public telephone networks. No Data Access Arrangements ({xe
"DAA"}DAAs) are required.

The MT5634HD8 is fully compatible with the standard AT command set, and is
therefore compatible with all popular communications software packages.

This user guide will help you to install, configure, test, and use the MT5634HD8.

Manual Organization

{xe "manual organization"}

Chapter 1 Introduction

This chapter describes the MT5634HD8 and its LED indicators, gives its technical
specifications, and provides a guide to the organization of the manual.

Chapter 2 Installation

This chapter describes how to install the MT5634HD8 into the CC9600 chassis.

Chapter 3 Command Mode Operation

This chapter provides an introduction to MT5634HD8 command mode fundamentals,
followed by a detailed explanation of each AT command, providing examples
where applicable.

Chapter 4 S-Registers

This chapter describes the MT5634HD8’s S-registers, which are used to store
various modem options.

Chapter 5 Warranty, Service, and Technical Support

This chapter provides the terms of the MT5634HD8’s warranty, instructions for
obtaining factory service, and information about Multi-Tech’s BBS and technical
support. Information on upgrading the MT5634HD8’s firmware is also provided.

«
...
6
7
8
9
10
...
»

Содержание CommPlete MT5634HD8




































































































Отзывы:

Нет отзывов