Multitech CommPlete MT5634HD8 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 99

Multitech CommPlete MT5634HD8 Скачать руководство пользователя страница 15

2 Installation

CommPlete Communications Server

9

✔

Ports that are connected to other apparatus are defined as SELV. To ensure con-
formity to EN 41003, ensure that these ports are only connected to the same type
on the other apparatus.

Pre-Installation Notes

Warning:

Direct interconnection (or connection by way of other apparatus) of ports

marked “SAFETY WARNING see instructions for use” with any other ports
(whether or not similarly marked) may produce hazardous conditions on the
network.

MultiTech strongly urges you to consult a qualified engineer before attempting to
make this type of connection.

•

All installation{ XE "installation" } must be done by a qualified service person.

•

To reduce emissions, be sure to use blanking plates to cover empty slots in the
CC9600 chassis.

•

Cable, wiring, and any other apparatus connected between the MT5634HD8K
modem and the point of connection to any speech band circuit shall comply with
the following:

1. The overall characteristics of the apparatus shall be such as to introduce no

material effect upon the electrical conditions presented to one another by
the modem and the speech band circuit.

2. The apparatus shall comprise only

a. apparatus approved for the purpose of connection between the modem

and a speech band circuit; and

b. cable and wiring complying with a code of practice for the installation

of equipment covered by this part of BS 6328 or such other requirements
as may be applicable.

Note:

Such apparatus may have been approved subject to limitations in its use.

Installation Procedure

1. Unpack the MT5634HD8 assembly from its factory packaging. (You may wish

to save the packaging for possible future use.)

2. Perform a visual inspection of the MT5634HD8. If you are concerned about its

condition, call Technical Support for instructions.

3. The MT5634HD8 must be installed in a segment in which a RASCard with a T1

module is installed. Turn off the RAS segment where the MT5634HD8 will be
installed. (Turn off power to this segment.)

4. Remove a blank device front panel or previous MT5634HD8 card from the RAS

segment used in step 3. Do not remove the back panel.

«
...
13
14
15
16
17
...
»

Содержание CommPlete MT5634HD8




































































































Отзывы:

Нет отзывов