Multitech CommPlete MT5634HD8 Скачать руководство пользователя страница 74

Страница: 74 / 99

MT5634HD8 User Guide

CommPlete Communications Server

Command

Values

Description

n = 0

Store Configuration

&W0 Store current settings in NVRAM; modem will

load these at power-on or with the ATZ
command instead of reading factory ROM
defaults.

n = 0–7

Result Codes and Call Progress Selection

Basic result codes (

CONNECT

only); does not

look for dial tone or busy.

Extended result codes (w/

CONNECT 1200

CONNECT

2400

, etc.); does not look for dial

tone or busy signal.

Extended result codes with

NO DIAL TONE

;

does not look for busy signal.

Extended result codes with

BUSY

; does not

look for dial tone.

*** X4

Extended result codes with

NO DIAL TONE

and

BUSY

Extended result codes with

NO DIAL TONE

and

BUSY

Extended result codes with

NO DIAL TONE

and

BUSY

Basic result codes with

NO DIAL TONE

and

BUSY

\ X

n = 0

XON/XOFF Pass-Through

*** \X0

Respond to and discard XON\XOFF
characters.

n = 0

Long Space Disconnect

*** Y0

Disable sending or responding to long space
break signal on disconnect.

n = 0

Select Stored Configuration for Hard Reset

*** &Y0 Select stored configuration 0 at power-up

(included for backward compatibility with
some software.)

n/a

Modem Reset
Reset modem to default values. Defaults come from
NVRAM if &W0 is set, from ROM if &W1 is set.

n=x

n = 0-3, x =
dialing string.

Store Telephone Number
Stores telephone dial string

x in memory location n.

Dial the stored number using the command
ATDS=

In dial

Dialing Pause

command

Comma; causes dialing pause for time set by S8 .

;

At end of dial
command

Return to Command Mode After Dialing
Semi-colon; causes immediate return to com mand
mode after dialing.

Содержание CommPlete MT5634HD8




































































































Результаты поиска

Содержание CommPlete MT5634HD8

Отзывы:

Multitech CommPlete MT5634HD8, Руководство пользователя, Страница: 74 / 99

Результаты поиска

Содержание CommPlete MT5634HD8

Отзывы: