Multitech CommPlete MT5634HD8 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 99

Multitech CommPlete MT5634HD8 Скачать руководство пользователя страница 38

MT5634HD8 User Guide

32

CommPlete Communications Server

I

n

Information Request{xe "AT commands:I"}{xe "Information Request
command"}

n = 0, 1, 2, 3, 4, or 9
Default: none

This command displays specific product information about your modem.

I0

or I returns the default speed and controller firmware version number. Use this

command to identify your modem’s firmware level before calling Multi-Tech
Technical Support. (This is the same as I3.)

I1

calculates and displays the ROM checksum (for example, 12AB).

I2

performs a ROM check, calculates and verifies the ROM checksum, and displays

the results (OK or ERROR).

I3

returns the default speed and controller firmware version number. Use this

command to identify your modem’s firmware level before calling Multi-Tech
Technical Support. (This is the same as I or I0.)

I4

returns the firmware version for the data pump (for example, 94).

I9

displays the country code (for example, NA Ver. 1).

&B

n

V.32 Auto Retrain{xe "AT commands:&B"}{xe "Auto Retrain
command"}

n = 1
Default: &B1

The &B1 command enables V.32 auto retrain.

&V

View Current Configuration{ XE "AT commands:&V" }{ XE "View
Current Configuration command" }{ XE "configuration:view current" }

Default: none

Use the &V command to display the active modem settings.

Flow Control Commands

{xe "flow control:commands"}

Flow control refers to the techniques used by data terminal equipment and the
MT5634HD8 to pause and resume the flow of information between them. It prevents
a device from accepting more data than it can handle. The MT5634HD8 implements
flow control{xe "flow control"} in both directions.

When the MT5634HD8 halts the flow of data, it is called flow control, and when
the computer halts the flow, it is called pacing{xe "pacing"}.

&M

n

Communications Mode{xe "AT commands:&M"}{xe "Communications
Mode command"}

n = 0
Default: &M0

The &M command enables asynchronous communications mode. This is the default.

«
...
36
37
38
39
40
...
»

Содержание CommPlete MT5634HD8




































































































Отзывы:

Нет отзывов