MULTIQUIP Stow C10PH8 страница 25 Скачать руководство пользователя

Страница: 25 / 50

C10SH8-PH8 CONCRETE MIXER • OPERATION AND PARTS MANUAL — REV. #0 (03/06/09) — PAGE 25

MAINTENANCE (MIXER)

TIRES/WHEELS/LUG NUTS

Tires and wheels are a very important and critical
components of the trailer. When specifying or replacing the
trailer wheels it is important the wheels, tires, and axle are
properly matched.

TIRES WEAR/INFLATION

Tire infl ation pressure is the most important factor in tire
life. Pressure should be checked cold before operation.

NOT

bleed air from tires when they are hot. Check infl ation

pressure weekly during use to insure the maximum tire life
and tread wear.

Table 8 (Tire Wear Troubleshooting) will help pinpoint the
causes and solutions of tire wear problems.

CAUTION

DO NOT

attempt to repair or modify a wheel.

DO NOT

install an inter-tube to correct a

leak through the rim. If the rim is cracked,
the air pressure in the inter-tube may cause

pieces of the rim to explode (break-off) with great force
and can cause serious eye or bodily injury.

CAUTION

ALWAYS

wear safety glasses when removing

or installing force fitted parts. Failure to
comply may result in serious injury.

Tire Wear Troubleshooting

Table 8.

Wear Pattern

Cause

Solution

Center

Wear

Over Infl ation

Adjust pressure to
particular load per
tire manufacturer

Edge
Wear

Under
Infl ation

Adjust pressure to
particular load per
tire manufacturer.

Side

Wear

Loss of
chamber or
overloading

Make sure load does
not exceed axle
rating. Align wheels.

Toe

Wear

Incorrect
toe-in

Align wheels.

Cupping

Out of
balance

Check bearing
adjustment and
balance tires.

Flat

Spots

Wheel lockup
and tire
skidding

Avoid sudden stops
when possible and
adjust brakes.

Go to Discount-Equipment.com

to order your parts

Содержание Stow C10PH8



















































Результаты поиска

Содержание Stow C10PH8

Отзывы:

Похожие инструкции для Stow C10PH8

Бренды по названию

Популярные бренды

MULTIQUIP Stow C10PH8, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание Stow C10PH8

Отзывы:

Похожие инструкции для Stow C10PH8

Бренды по названию

Популярные бренды