MULTIQUIP Stow C10PH8 Скачать руководство пользователя страница 29

Страница: 29 / 50

PAGE 28 — C10SH8-PH8 CONCRETE MIXER • OPERATION AND PARTS MANUAL — REV. #0 (03/06/09)

TROUBLESHOOTING (ENGINE)

Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of
a breakdown, please take a remedial action following the
diagnosis based on the Troubleshooting (Tables 10 and 11)

information shown below and on the next page. If the problem
cannot be remedied, please leave the unit just as it is and
consult our company’s business offi ce or service plant.

Engine Troubleshooting

Table 10.

Symptom

Possible Problem

Solution

Diffi cult to start

Fuel is available but spark plug will not
ignite (power available at high tension
cable).

Ignition plug being bridge?

Check ignition system.

Carbon deposit at ignition?

Clean or replace ignition.

Short circuit due to defective insulators?

Replace insulators.

Improper spark gap?

Set spark plug gap to the correct gap.

Fuel is available but spark plug will not
ignite (power

NOT

available at high

tension cable).

Short circuit at stop switch?

Check stop switch circuit. Replace stop
switch if defective.

Ignition coil defective?

Replace ignition coil.

Fuel is available and spark plug ignites
(compression

normal

Muffl er clogged with carbon deposits?

Clean or replace muffl er.

Fuel in use inadequate (water, dust)?

Flush fuel system and replace with fresh
fuel.

Air cleaner clogged?

Clean or replace air cleaner.

Fuel is available and spark plug ignites
(compression

low

Defective cylinder head gasket?

Tighten cylinder head bolts or replace
head gasket.

Cylinder worn?

Replace cylinder.

Spark plug loose?

Tighten spark plug.

Operation not satisfactory

Not enough power available
(compression normal, no miss-fi ring).

Air cleaner clogged?

Air in fuel line?

Bleed (remove air) from fuel line.

Fuel level in carburetor fl oat chamber
improper?

Adjust carburetor fl oat.

Carbon deposits in cylinder?

Clean or replace cylinder.

Not enough power available
(compression normal, miss-fi ring).

Ignition coil defective?

Flush fuel system and replace with fresh
fuel.

Ignition plug often shorts?

Replace ignition wires, clean ignition.

Fuel in use inadequate (water, dust)?

Flush fuel system and replace with fresh
fuel.

Rotational speed fl uctuates.

Governor adjustment improper?

Adjust governor to correct level.

Governor spring defective?

Clean or replace ignition.

Fuel fl ow erratic?

Check fuel line.

Air taken in through suction line?

Check suction line.

Recoil starter not working properly.

Dust in rotating part?

Clean recoil starter assembly.

Spring failure?

Replace spiral spring.

Go to Discount-Equipment.com

to order your parts

Содержание Stow C10PH8



















































Результаты поиска

Содержание Stow C10PH8

Отзывы:

Похожие инструкции для Stow C10PH8

Бренды по названию

Популярные бренды

MULTIQUIP Stow C10PH8, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание Stow C10PH8

Отзывы:

Похожие инструкции для Stow C10PH8

Бренды по названию

Популярные бренды