MULTIQUIP Stow C10PH8 страница 18 Скачать руководство пользователя

Страница: 18 / 50

PAGE 18 — C10SH8-PH8 CONCRETE MIXER • OPERATION AND PARTS MANUAL — REV. #0 (03/06/09)

SAFETY CHAIN CONNECTION

Reference Figure 4 for the installation of the Safety
Chain.

Tow Bar to Mixer Connection

Insert the tow bar through the round opening at the

bottom of the mixer stand.

Align the hole on the tow bar with the hole on the mixer
frame, and insert 1/2-inch bolt through tow bar and
frame. Secure tow bar to frame with 1/2-inch nylock
nut. Tighten to 40 ft.-lbs.

CAUTION

NEVER

tow the mixer with the safety chain removed.

The safety chain is intended to prevent complete
separation of the mixer from the towing vehicle in the
event of a tow bar failure.

Route the safety chain through the holes just above the

tow bar, located on each side of the mixer stand.

Loop the chain together and place under the tow bar.
Secure the loop with the connector link.

Extend the safety chain along the length of the tow bar,

looping it through the tow bar's connector link. Remove
any excess chain slack.

Connect the free end of (clevis safety hook) the safety

chain to the towing vehicle. Remember,

it is critical

that the length of the chain be properly adjusted

, to

prevent the

draw bar

and the front of the mixer stand

from dropping to the the ground (contact) in the event
the draw bar becomes disconnected from the towing
vehicle.

SAFETY CHAIN

CONNECTOR LINK

TOW BAR

CONNECTOR LINK

SAFETY CHAIN

CLEVIS SAFETY HOOK

(TOWING VEHICLE)

MIXER

STAND

SAFETY CHAIN

1/2-INCH BOLT,

GRADE 5

1/2-INCH NYLOCK

NUT, GRADE 5

STEP 1

STEP 2

STEP 3

STEP 4

Tow Bar and Safety Chain Installation

Figure 4.

Go to Discount-Equipment.com

to order your parts

Содержание Stow C10PH8



















































Результаты поиска

Содержание Stow C10PH8

Отзывы:

Похожие инструкции для Stow C10PH8

Бренды по названию

Популярные бренды

MULTIQUIP Stow C10PH8, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание Stow C10PH8

Отзывы:

Похожие инструкции для Stow C10PH8

Бренды по названию

Популярные бренды