MULTIQUIP MC12PH Скачать руководство пользователя

Страница: 19 / 79

PAGE 18 — MC12PH CONCRETE MIXER • OPERATION AND PARTS MANUAL — REV. #1 (09/02/15)

TOW BAR TO MIXER CONNECTION

Reference Figure A for the installation of the safety chain.
1. Insert the tow bar through the round opening at the

bottom of the mixer stand.

Align the hole on the tow bar with the hole on the mixer

frame, and insert 1/2-inch bolt through tow bar and

frame. Secure tow bar to frame with 1/2-inch nylock

nut. Tighten to 40 ft.-lbs.

Figure A. Tow Bar and Safety Chain Installation

CAUTION

NEVER

tow the mixer with the safety chain removed.

The safety chain is intended to prevent complete

separation of the mixer from the towing vehicle in the

event of a tow bar failure.

2. Route the safety chain through the holes just above

the tow bar, located on each side of the mixer stand.

Loop the chain together and place under the tow bar.

Secure the loop with the connector link.

3. Extend the safety chain along the length of the tow bar,

looping it through the tow bar's connector link. Remove

any excess chain slack.

4. Connect the free end of (connector link) the safety

chain to the towing vehicle. Remember it is critical

that the length of the chain be properly adjusted, to

prevent the draw bar and the front of the mixer stand

from dropping to the the ground (contact) in the event

the draw bar becomes disconnected from the towing

vehicle.

CAUTION

DO NOT

tow or lift the mixer unless the mixing drum

is completely empty.

CAUTION

Use a lifting device to lift tow bar onto vehicle coupler. If

lifting device is not available, have 2 persons of similar

height lift the tow bar. When lifting, do not attempt to lift

by bending forward. Bend hips and knees to squat down

to your load, keep it close to your body, and straighten

your legs to lift.

SAFETY CHAIN CONNECTION

Discount-Equipment.com

Содержание MC12PH
















































































Результаты поиска

Содержание MC12PH

Отзывы:

Похожие инструкции для MC12PH

Бренды по названию

Популярные бренды

MULTIQUIP MC12PH, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание MC12PH

Отзывы:

Похожие инструкции для MC12PH

Бренды по названию

Популярные бренды