MULTIQUIP MC12PH Скачать руководство пользователя страница 16

Страница: 16 / 79

MC12PH CONCRETE MIXER • OPERATION AND PARTS MANUAL — REV. #1 (09/02/15) — PAGE 15

BASIC COMPONENTS

Figure 2. Mixer Major Components

NOTE:
SHOWN FOR CLARITY

ACTUAL LOCATION IS ON OPPOSITE SIDE

Plastic Mixing Drum

— The Multiquip MC12PH uses

a 12 cu. ft

plastic

mixing drum. This drum is to be used

for mixing of concrete. Always clean the drum after

each use.

DO NOT

use this mixing drum for the mixing

volatile or hot liquids

Dump Latch

— To rotate the mixing drum, this latch

must be in the up position. To lock the drum, place the

latch in the down position.

Dump Gear Guard

—

NEVER

operate the mixer

with this guard removed. Its purpose is to prevent dirt

and debris from entering the dump gear. In addition

operator clothing could become entangled in the dump

gear, causing severe injury and bodily harm.

Handwheel

— Turn this wheel clockwise or

counterclockwise to rotate the mixing drum. Remember

the dump latch must be in the

up position

in order for

the mixing drum to be rotated.

Safety Chain

— This mixer uses a 3/16-inch thick, 72

inches long zinc-plated saftey chain.

ALWAYS

connect

the safety chain when towing.

Tow Bar

— This mixer uses various towing bars, please

reference the frame assembly drawing and parts list

in this manual to determine which tow bar meets your

requirements.

Cantilever Suspension

— This mixer uses a cantilever

type suspension. Check the mounting hardware for

bolt hole elongation and tightness. See maintenance

section of this manual for recommended maintenance.

Chock Blocks

— Place these blocks (not included as

part of the mixer package) under each mixer wheel

to prevent rolling, when mixer is not connected to the

towing vehicle.

Tires Ply

— The tire ply (layers) number is rated in

letters. This mixer uses 13-inch 2-ply tires. Replace

with only recommended type tires.

10.

ON/OFF Switch

— This switch is located on the side

of the mixer frame. When activated it will shut down the

engine. Pull out when starting the engine.

11.

Cabinet/Latch

— Encloses engine and electric motor.

NEVER

run mixer with cabinet removed. Use latches

to secure engine compartment cabinet.

12.

Mixing Blades

— Used for the mixing of concrete.

When blades show signs of wear, replace the blades.

Discount-Equipment.com

Содержание MC12PH
















































































Результаты поиска

Содержание MC12PH

Отзывы:

Похожие инструкции для MC12PH

Бренды по названию

Популярные бренды

MULTIQUIP MC12PH, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание MC12PH

Отзывы:

Похожие инструкции для MC12PH

Бренды по названию

Популярные бренды